- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
10-31-2024, 10:53 AMBikeracer2020 replied to a thread Air compressor keeps running while 3D printing in General 3D Printing DiscussionConsidering that you have posted about an air compressor in a forum dedicated to 3D printing I assume you will know where to get a discombobulater,...2 replies | 666 view(s)
-
10-30-2024, 03:29 PMBikeracer2020 replied to a thread Carbon Fiber Filament Recommendations in 3D Printer Parts, Filament & MaterialsI don't know what your set up is, but wonder if it might warrant making a fixture rather than use two vices.5 replies | 989 view(s)
-
10-30-2024, 03:09 PMBikeracer2020 replied to a thread Carbon Fiber Filament Recommendations in 3D Printer Parts, Filament & MaterialsThis might be what you want... https://uk.store.bambulab.com/collections/fiber-reinforced/products/ppa-cf5 replies | 989 view(s)
-
10-30-2024, 02:43 PMI returned my Qidi XMAX 3, the software was buggy, parts needed replacing, the heated chamber did nothing to stop prints warping, the file transfer...4 replies | 1263 view(s)
-
10-30-2024, 11:48 AMOf the printers you mention, Prusa do their own thing and seem reliable with good after sales and back up service. The user experience with the...4 replies | 1263 view(s)
-
10-30-2024, 03:12 AMBikeracer2020 replied to a thread Why my printer leaves small lumps/bits on surface in General 3D Printing DiscussionA picture of the bed leveling square would help to see the surface. The 'Z' offset might need adjusting in the slicer settings. I don't use Cura,...1 replies | 966 view(s)
-
10-26-2024, 02:43 AMBikeracer2020 replied to a thread Printing problem on Ender 3 after change to 4.2.7 mainboard in Tips, Tricks and Tech HelpConsidering this happened after changing the motherboard, perhaps putting the old one back in might be worth trying.7 replies | 6011 view(s)
-
10-25-2024, 09:49 AMBikeracer2020 replied to a thread Printing problem on Ender 3 after change to 4.2.7 mainboard in Tips, Tricks and Tech HelpDid you do a flow rate check, also check the "e" steps.7 replies | 6011 view(s)
-
10-25-2024, 04:29 AMIt's called 'manage attachments' lower down the page where you type in your post.2 replies | 5313 view(s)
-
10-24-2024, 08:58 AMThere is a flow rate calibration file in the pull down menu in Orcaslicer4 replies | 5796 view(s)
-
10-24-2024, 01:58 AMBikeracer2020 replied to a thread Issues with a sort of ringing and jagged cuts with print in Tips, Tricks and Tech HelpI've seen clips on Youtube about the vertical ringing lines on prints and there seems to be some evidence that it's caused by harmonics from the...3 replies | 4562 view(s)
-
10-23-2024, 01:00 PMMight be better to tighten nozzle when heat block temperature is approx 20 degrees higher than your normal temps, this will make a better seal on the...4 replies | 5796 view(s)
-
10-23-2024, 12:46 PMBikeracer2020 replied to a thread Best 3D printer for me? Comment advice. in General 3D Printing DiscussionI've got an X1C with the AMS if that helps, it's been a totally different user experience for me with the Bambu Labs machine. It was basically...114 replies | 278965 view(s)
-
10-13-2024, 08:32 AMBikeracer2020 replied to a thread Printing problem on Ender 3 after change to 4.2.7 mainboard in Tips, Tricks and Tech HelpIt often seems to happen mainly in one area, search Youtube for under extrusion videos.7 replies | 6011 view(s)
-
10-13-2024, 05:01 AMBikeracer2020 replied to a thread Printing problem on Ender 3 after change to 4.2.7 mainboard in Tips, Tricks and Tech HelpThe holes look like under extrusion. There is a flow rate calulator in the calibration menu in Orca slice7 replies | 6011 view(s)
-
10-12-2024, 08:21 AMBikeracer2020 replied to a thread How do I print a temp tower? in 3D Printer Parts, Filament & MaterialsThere is a ready made adjustable temperature tower in the calibration menu in Orcaslicer3 replies | 4668 view(s)
-
10-10-2024, 05:36 AMBikeracer2020 replied to a thread Z-Axis Inaccuracy on Creality Ender 3 V2 Printer in General 3D Printing DiscussionTry making the vertical height of your print a multiple of the layer height.1 replies | 3202 view(s)
-
10-05-2024, 02:49 AMBikeracer2020 replied to a thread Need to design a thumb ... do cad programs use nodes? in 3D Modeling, Design, ScannersJust the free version with a limit of ten saved projects, a few features are disabled but it's adequate for my limited ability.3 replies | 4057 view(s)
-
10-04-2024, 10:15 AMBikeracer2020 replied to a thread Need to design a thumb ... do cad programs use nodes? in 3D Modeling, Design, ScannersI don't know Tinkercad, but in Fusion 360 the spline tool puts nodes on.3 replies | 4057 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 685
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Carbon Fiber Filament...
Yesterday, 04:58 PM in 3D Printer Parts, Filament & Materials