- Tab Content
- fred_dot_u's Activity
- About Me
- Tab Content
-
Older Activity
-
01-11-2021, 05:20 AMfred_dot_u replied to a thread Cura Intermittent Retraction Problem. Retraction Not perfromed randomly. in General 3D Printing DiscussionHere's a tosser; grab a copy of Prusa Slicer 2 and a profile for your printer and see if anything changes. It's a free program and won't screw up...4 replies | 487 view(s)
-
01-10-2021, 01:21 PMThe phrasing and lack of presence on the forum leads me to believe this is a bot generated response. It's barely on topic, although better than some...30 replies | 3260 view(s)
-
01-09-2021, 07:42 PMfred_dot_u replied to a thread Cura Intermittent Retraction Problem. Retraction Not perfromed randomly. in General 3D Printing DiscussionFor a new guy here, your post is rather well done, comprehensively described. Considering all the things you've done to narrow the problem, I'm...4 replies | 487 view(s)
-
01-08-2021, 07:48 PMWhat percentage of infill do you have set? Can you either attach your STL file or link it from the source? The brim has an even surface, which bodes...7 replies | 506 view(s)
-
01-08-2021, 06:01 PMOnce you turn on the supports, you should see how they are placed in the preview. What slicer are you using? There are adjustments available for...7 replies | 506 view(s)
-
01-08-2021, 05:41 PMYou'll want to locate the setting in your slicer for supports. Turn on supports and the slicer will create a print file that builds a series of walls...7 replies | 506 view(s)
-
01-04-2021, 07:09 PMI suspect that the post was merely to get past moderation, preparing to post garbage in the near future.9 replies | 1118 view(s)
-
01-04-2021, 05:48 PMFDM is a method of 3D printing, as is SLA. One is filament deposition, the other stereolithography, sometimes called MSLA for masked...6 replies | 924 view(s)
-
01-04-2021, 04:46 PMIt sounds as though the 47 inches would be the length of the hull. That's going to require a rather large printer, unless you can accept segmenting...6 replies | 924 view(s)
-
01-04-2021, 04:19 PMare you hoping to have the boat printed in one piece, or are the STL files of a segmented model?6 replies | 924 view(s)
-
01-02-2021, 06:02 PMfred_dot_u replied to a thread My Finder printer gets halfway through print then cools? Help! in Tips, Tricks and Tech HelpThe attachment works, unfortunately in such a manner as to let me know it's not in the g-code. The early M104 line reads M104 S220 T0, which says set...7 replies | 624 view(s)
-
01-02-2021, 03:18 PMfred_dot_u replied to a thread My Finder printer gets halfway through print then cools? Help! in Tips, Tricks and Tech Helpcheck the last line in this linked web page it should allow you to download the g-code and then attach it here for checking. It's an...7 replies | 624 view(s)
-
01-02-2021, 02:19 PMfred_dot_u replied to a thread My Finder printer gets halfway through print then cools? Help! in Tips, Tricks and Tech HelpI realize now that your 40-50 percent reference was for amount of print completed. A little slow on my part... You can see the M104 S0 T0 code in...7 replies | 624 view(s)
-
01-02-2021, 05:33 AMfred_dot_u replied to a thread My Finder printer gets halfway through print then cools? Help! in Tips, Tricks and Tech Helpbased on your phrasing, your print isn't changing temperature, your nozzle temperature is dropping. The "40-50 percent" reference is also ambiguous,...7 replies | 624 view(s)
-
12-28-2020, 05:07 PMIt would not be so much that it is not compatible as more likely it's lower quality than one might prefer. Attack the nozzle height consideration...16 replies | 1286 view(s)
-
12-28-2020, 11:23 AMThose are all good numbers/data and I'll stand by my suggestion, and support the others' as well. The suggestion about too close to the bed is...16 replies | 1286 view(s)
-
12-27-2020, 07:40 PMI'm too often surprised at the vitriol that pops up now and then. I've learned long ago to keep my posts objective and avoid "you did this," or "you...7 replies | 819 view(s)
-
12-27-2020, 06:21 PMIf you recognize that you are posting to a forum in which everyone is entitled to respond, and that those responses may well include opinions, you'll...7 replies | 819 view(s)
-
12-27-2020, 05:40 PMIf you find a particular aspect to be problematic or intimidating, post here with a question or two with details and someone will have an answer. It...9 replies | 1118 view(s)
-
12-27-2020, 02:55 PMYou will get many dozen recommendations. What have you tried or found thus far? A few of us here are fans of OpenSCAD, but it's not for everyone....9 replies | 1118 view(s)
-
12-27-2020, 02:50 PMA lot of missing information is required for someone to be of assistance. Bed temperature, nozzle temperature, printing material, any adhesive used. ...16 replies | 1286 view(s)
-
12-26-2020, 09:36 PMfred_dot_u replied to a thread WANT TO BUY "SIL Hybrid" 3D Printed! in General 3D Printing DiscussionThat's an impressive bit of kit for an archer.1 replies | 339 view(s)
-
12-19-2020, 08:58 PMfred_dot_u replied to a thread Modeling app that does offset booleans? in 3D Modeling, Design, ScannersEven though it's challenging to navigate to the correct license location, Fusion 360 is still free for hobbyists and is more like OnShape than...5 replies | 1019 view(s)
About fred_dot_u
Basic Information
Statistics
Total Posts
- Total Posts
- 500
- Posts Per Day
- 0.21
General Information
- Last Activity
- 01-15-2021 12:03 PM
- Join Date
- 06-24-2014
‘Hover’ printing failure
01-15-2021, 12:00 PM in Tips, Tricks and Tech Help