- Tab Content
- airscapes's Activity
- About Me
-
Older Activity
-
01-15-2021, 04:25 PMyeah Trolley, think Harry Potter.. cart with wheels, least that is what I imagined as a Yank!7 replies | 568 view(s)
-
01-08-2021, 12:11 PMairscapes replied to a thread Nozzle repeatedly clogging while printing Ninjaflex TPU in 3D Printer Parts, Filament & MaterialsTPU needs a good filament drive that has no place for the filament to go but into the hot end, direct drive does not make it so.. you should have a...3 replies | 948 view(s)
-
01-03-2021, 09:22 AMairscapes replied to a thread Temperature resets to 0 mid-print Prusa i3 MK1 in Tips, Tricks and Tech HelpYou might want to do a quick search of the Prusa forum.. would expect you will find a more exacting post with the problem and fix...6 replies | 1470 view(s)
-
01-02-2021, 03:41 PMairscapes replied to a thread Temperature resets to 0 mid-print Prusa i3 MK1 in Tips, Tricks and Tech Helpbad thermistor, hotend, or cabling.. Most likely thermistor is bad or wire almost broken.6 replies | 1470 view(s)
-
01-02-2021, 03:14 PMairscapes replied to a thread Cannot get the right temperature for petg in 3D Printer Parts, Filament & MaterialsOn my MakeGear I use 235C and 70C for eSun and Overture PETG2 replies | 494 view(s)
-
12-30-2020, 04:31 PMairscapes replied to a thread shrink/warp printing multiple parts simultaneously in Tips, Tricks and Tech HelpGreg, where are you located? Any where near Philadelphia PA USA?10 replies | 1370 view(s)
-
12-30-2020, 09:29 AMAs you gain experience you will find it is best to keep the fabrication method limitations in mind when you are designing a part. Such as print...5 replies | 455 view(s)
-
12-29-2020, 02:45 PMairscapes replied to a thread shrink/warp printing multiple parts simultaneously in Tips, Tricks and Tech HelpOther than the one corner at 3.12 being a bit low, which could cause adhesion issues in that area, the rest look fairly good! Another thing to...10 replies | 1370 view(s)
-
12-29-2020, 08:30 AMa .1mm layer height would reduce the step height and using a slicer with ironing function would help on smoothing the top surface a little in this...5 replies | 455 view(s)
-
12-28-2020, 07:46 PMairscapes replied to a thread shrink/warp printing multiple parts simultaneously in Tips, Tricks and Tech Helpto be honest should be better printing more than one at a time.. try putting a line of them down the center of the bed and see what happens.. You do...10 replies | 1370 view(s)
-
12-28-2020, 06:39 PMairscapes replied to a thread shrink/warp printing multiple parts simultaneously in Tips, Tricks and Tech HelpAnother thing that can cause issues is a bed that is not level and a Z offset that is incorrect and or incorrect extrusion multipier. To check use...10 replies | 1370 view(s)
-
12-28-2020, 06:12 PMairscapes replied to a thread shrink/warp printing multiple parts simultaneously in Tips, Tricks and Tech HelpSo.. what does the part look like.. does it have pointy corners? If so try and add a fillet to round the corner if you designed the part. What PLA...10 replies | 1370 view(s)
-
12-22-2020, 08:58 PMairscapes replied to a thread Nozzle repeatedly clogging while printing Ninjaflex TPU in 3D Printer Parts, Filament & MaterialsOk, no idea about your printer but here is what I do with my Makergrear m2 Had to replace the OEM extruder housing with one that had been modified...3 replies | 948 view(s)
-
12-20-2020, 01:10 PMLook at the Prusa line.. there is NO plug and play, but Prusa is closest.8 replies | 1178 view(s)
About airscapes
Basic Information
Statistics
Total Posts
- Total Posts
- 464
- Posts Per Day
- 0.48
General Information
- Last Activity
- Today 11:00 AM
- Join Date
- 05-20-2018
‘Hover’ printing failure
01-15-2021, 12:00 PM in Tips, Tricks and Tech Help