- Tab Content
- Roberts_Clif's Activity
- About Me
- Friends
- Tab Content
-
Older Activity
-
10-12-2024, 08:01 AMRoberts_Clif replied to a thread How do I print a temp tower? in 3D Printer Parts, Filament & MaterialsIf using an STL file you will need to set temp correct temp at the designated spot. If not then I have been doing it wrong for a long 8 year time...3 replies | 1225 view(s)
-
10-11-2024, 08:10 AMI created my first model knowing very little about Cad, I heard about Fusion 360 Free for Hobbyist downloaded and installed to software. Knowing...1 replies | 1256 view(s)
-
10-09-2024, 10:38 AMRoberts_Clif replied to a thread prusa mk3s: first layer lifting in a ripping fashion in Tips, Tricks and Tech HelpCurrently I am trying to print on this surface with no luck. IdeaFormer 256x268mm Anycubic Kobra 3 Compatible 3D Printer Build Plate, Spring Steel...7 replies | 3747 view(s)
-
10-01-2024, 09:17 PMRoberts_Clif replied to a thread Vivedino Troodon 2.0 Printing issues. in Tips, Tricks and Tech HelpNot sure exactly what I am looking for. Well I see a solid layer below a interweaving mesh topped with a 2nd solid top layer. This design looks...5 replies | 3775 view(s)
-
09-30-2024, 07:17 PMRoberts_Clif replied to a thread Vivedino Troodon 2.0 Printing issues. in Tips, Tricks and Tech HelpYou are welcome. I have had New filament just removed from packaging cause me similar problems. Though tuning a 3D Printer can be quite...5 replies | 3775 view(s)
-
09-28-2024, 10:24 AMRoberts_Clif replied to a thread prusa mk3s: first layer lifting in a ripping fashion in Tips, Tricks and Tech HelpYou are welcome. I have my 3D printer setup to print the first layer at 32% then the remaining layers at 72-82%. This is relative to which...7 replies | 3747 view(s)
-
09-27-2024, 09:03 PMRoberts_Clif replied to a thread Vivedino Troodon 2.0 Printing issues. in Tips, Tricks and Tech HelpSometime it is not easy deduce the cause of a missed print. Have had prints where the filament I was using was spliced with higher temperature...5 replies | 3775 view(s)
-
09-27-2024, 08:07 PMRoberts_Clif replied to a thread prusa mk3s: first layer lifting in a ripping fashion in Tips, Tricks and Tech HelpThe only time I get is when I try to 3D Print the first layer too fast. Sometimes 1st and 2nd layers then it will finish 3D printing perfectly.7 replies | 3747 view(s)
-
09-21-2024, 08:06 PMRoberts_Clif replied to a thread My stepper motor on Ender 3 S1 pro is very loud in Tips, Tricks and Tech HelpCheck the lead screws it sounds like the side making the most noise could have too much tension an could be out of alignment. Once my 3D Printer the...1 replies | 4409 view(s)
About Roberts_Clif
Basic Information
About Roberts_Clif
- Location:
- Washington State, USA
- Occupation:
- Electroncis Tech / IT / Programmer
- Thingiverse:
- Roberts_Clif
Statistics
Total Posts
- Total Posts
- 1,163
- Posts Per Day
- 0.43
General Information
- Last Activity
- Today 08:21 AM
- Join Date
- 06-12-2017
Printing problem on Ender 3 after...
Yesterday, 08:32 AM in Tips, Tricks and Tech Help