Roberts_Clif
Staff Engineer

3DP11 Red is a 12 volt 3D Printer, while Blu is a 24volt 3D Printer. Red came with a Z-Axis end-stop manual switch, while Blu came with a Z-Axis...

The Board is an ATmega2560 it will use #define MOTHERBOARD BOARD_MKS_BASE_14 As it has 5 Stepper motor Drivers for use with X, Y, Z , E0 and...

Hello; What 3D Printer do you have?

Most solid frame 3D Printers could print the charms. I would look away from any 3D Printer that in made with a plastic frame and look at those...

We do not have any of these where I live but found this https://www.youtube.com/watch?v=GZpdDch2o4M

Learning the techniques of adding supports on complex models can take trial an error, there is not one setting that is a fix all for all models. ...

Never Heard of Just3DPrint in fact searched the Web an could not find them there either.

With an enclosure printing ABS at 232C with the bed set to 96C Have 3D Printer over 2 year now with these settings.

Thought I had killed a controller because I flashed it incorrectly, though keep trying and finally brought it back to life.

Plus One more who is to say they don't keep a copy of your Creations.

I had a similar problem rerouting the stepper cables away from the controller as quickly as possible and shielding the controller corrected. I...

I do not change the nozzles very often though when nozzles have to be changed they are in petty bad shape. Only the left most nozzle is good all...

PrusaSliscer with my Hictop 3DP11 an 3DP12 3D Printers. Here is the Finished Print. Artifacting almost non-existent. Printed in 3hurs 48 minutes...

I am trying a Print with a modified layer thickness across the lower area to see how well this will change the terraces. The dark Blue layer...

Posted your comment on Prusa forum an hopefully some will post a solution. an here is what the best had to say. "the Mk1 is largely the same as...

1. Tetris 2. Super Mario 64 3. The Legend of Zelda 4. Doom 5. Ms. Pac-Man

You have a Prusa i3 I would think that you would want to use the best slicer PrusaSlicer 2.3.0 rc2 Has configurations for your 3D Printer. Without...

This is called under-extrusion. I call it Swiss Cheese. Mine was caused by having the Slicer set to 3mm filament when I was using 1.76mm...

Slic3r is good Though PrusaSlicer 2.3.0 rc2 Being a offshoot if Slic3r is a better choice While you are trying give it a try. P.S. PrusaSlicer...

Printed at 0.32mm layer height no layer shift

It appears that you are having some real problems with layer shifting. Possible Causes : Eccentric nuts are over tightened. Stepper motor...

Here is a better explanation than I can give you.

Am talking to Adafruit as have a bad Raspberry Pi 3B hoping to get warranty on, then I will be purchasing a pair of raspberry Pi 4 2GB's

After Returning to the OctoPrint web site and reading found this updated Download information Octop1 0.17.0 Although below it states Do...

I was just looking Walmart online store has some and the price is not that too bad!

Cheapest possible window cleaner you can get. That way there is not other chemicals that could render cleaning useless.

The model is releasing from the bed so you need to lower the nozzle Depending on your firmware this can be done using the LCD an changing the...

A raspberry 3 can run one 3D Printer using Octoprint trying to operate two would most likely be too much for a single Raspberry Pi 3. Run a single...

The SD cards that come with some 3D Printers are only good for one thing the circle file (" garbage can "). Purchase a few new ones format using a...

I hate using rafts they are horrible, most of my models have a flat surface making the rafts unnecessary. though a heated print chamber sure make a...