- Tab Content
- Roberts_Clif's Activity
- About Me
- Friends
- Tab Content
-
Older Activity
-
Today, 10:24 AMI am having problems sense purchasing this newer what is called a smooth spring steel print bed. Until I gouged it with the nozzle and covered if...7 replies | 3950 view(s)
-
Yesterday, 04:21 PMIs the layer shift on the X or Y or on both axis's Have you watched the print, does the nozzle seen to run away then return and continue like...4 replies | 312 view(s)
-
Yesterday, 10:25 AMIn the image below is this the shifting you are seeing https://3dprintboard.com/attachment.php?attachmentid=19882&stc=1&d=1732980254...4 replies | 312 view(s)
-
11-26-2024, 06:57 PMhttps://3dprintboard.com/attachment.php?attachmentid=19875&stc=1&d=1732665026 Download Marlin 2.1.2.5 " Download and Configurations files. Unzip...13 replies | 3548 view(s)
-
11-25-2024, 10:39 AMWhile the core functionality remains similar, some minor tweaks might be necessary depending on the specific Ender 3 model (like Ender 3 Pro, Ender...13 replies | 3548 view(s)
-
11-24-2024, 12:33 PMI appears found most of the information Just need the exact name of the Ender 3 Printer Ender 3, Ender 3 Max, Ender 3 Pro, Ender 3 S1, S2 , V2, V2...13 replies | 3548 view(s)
-
11-23-2024, 10:34 PMDo not know the difference what controller did that one have was it the 4.2.2 or the 1.1.5 with BL Touch or end stop switch.13 replies | 3548 view(s)
-
11-23-2024, 10:24 PMDo not see much difference mine controller has a ARM-level Cortex-M4 168 MHz STM32F407ZGT6 chip, your uses LPC1769 120MHZ chip. My Marlin 2.1.2.2...13 replies | 3548 view(s)
-
11-23-2024, 09:45 PMThis is the controller I just purchased it is a BigTreeTech Pro V1.1 with TMC 2209 drivers. I have already configured marlin though still designing...13 replies | 3548 view(s)
-
11-23-2024, 08:58 PMI do not see a problem with helping you out here. I have updated my 3D Printers from Marlin-1.1.0-RC6_Hici3-1.1.0-RC6_CL061316a to Marlin-2.1.2 And...13 replies | 3548 view(s)
-
11-20-2024, 09:47 AMI had this happen now a again normally if if I raise the nozzle a little the nozzle will print over this bump. What i see is high spot on the bed...1 replies | 3502 view(s)
-
11-17-2024, 02:42 PMRoberts_Clif replied to a thread how to change gcode for changing filament in General 3D Printing DiscussionIn marlin firmware this is done during coding. In Configuration_adv.h > search for "// @section advanced pause" There is a section for "Advanced...2 replies | 4420 view(s)
-
11-10-2024, 08:57 AMI suggest the you check the solder connections for the Bed heater Mosfet , see it there is a cold solder connection on main board.1 replies | 7531 view(s)
About Roberts_Clif
Basic Information
About Roberts_Clif
- Location:
- Washington State, USA
- Occupation:
- Electroncis Tech / IT / Programmer
- Thingiverse:
- Roberts_Clif
Statistics
Total Posts
- Total Posts
- 1,180
- Posts Per Day
- 0.43
General Information
- Last Activity
- Today 10:28 AM
- Join Date
- 06-12-2017
Marlin Compiling
11-26-2024, 06:57 PM in General 3D Printing Discussion