- Tab Content
- Roberts_Clif's Activity
- About Me
- Tab Content
-
Older Activity
-
02-17-2019, 09:40 AMRoberts_Clif replied to a thread Want to add smart display to this board, is it possible? in 3D Printers (Hardware)It appears that this was a Kick-Starter project from 2013 Specifications: Atmel AT90USB1286 microcontroller 4-axis, 4 endstop control...6 replies | 594 view(s)
-
02-17-2019, 09:24 AMRoberts_Clif replied to a thread When will we be 3D printing all houses? in General 3D Printing DiscussionI do not believe this will happen anytime soon, you may see 3D Printed houses for the less fortunate sooner than you would think. This will allow...5 replies | 168 view(s)
-
02-16-2019, 02:01 PMI can not explain why the Temp Tower came out so well and the Next print the Extruder Tension fix so bad. Post the setting you used on the tension...37 replies | 2081 view(s)
-
02-15-2019, 11:23 AMI am looking at this E-Bay Delta wanted to get some information about but can not. If any one has purchased this Item would except any information...1 replies | 122 view(s)
-
02-13-2019, 07:54 PMWould venture to guess that the filament got tangled.1 replies | 143 view(s)
-
02-13-2019, 07:40 PMExcellent!!! Any other Questions.37 replies | 2081 view(s)
-
02-13-2019, 07:44 AMIt is OK. That it did not finish you got good results you may want to search and print a new tower with higher printer temps.37 replies | 2081 view(s)
-
02-13-2019, 07:34 AMThe one I looked at was 139.00 Buy It Now) I have 3 of the SN04-N and 5 of the TLW3MC2 not worried about auto-bed leveling, would install Marlin...6 replies | 441 view(s)
-
02-12-2019, 09:48 AMI sent a Message to them on E-Bay to get more information about this Delta have not heard back.6 replies | 441 view(s)
-
02-11-2019, 01:56 PMI do not know was only making a statement, Have you tried to print a temperature tower. Do not like the one I selected More here Your...37 replies | 2081 view(s)
-
02-10-2019, 07:06 PMWhat are you using for Nozzle and Bed temperature. What print speed percent is Cura set to. What you are telling me is that you may have too low...37 replies | 2081 view(s)
-
02-09-2019, 09:05 AMHave never printed on Glass, though believe it would be similar as any other surface. They say to use Elmer's glue sticks for best adhesion. Can...37 replies | 2081 view(s)
-
02-05-2019, 08:58 AMRoberts_Clif replied to a thread Strange DEFAULT_AXIS_STEPS_PER_UNIT setting for Marlin in General 3D Printing DiscussionDid you install the 3 jumpers that are under the Driver modules. on the ramps. https://www.youtube.com/watch?v=l7QgDSAlBdg2 replies | 261 view(s)
-
01-29-2019, 10:24 AMMy typing and my thoughts are working at different speeds, so sometimes all the thoughts do not make to the unedited typed Post.17 replies | 953 view(s)
-
01-29-2019, 09:57 AMIt appears that your gear that moves the filament is not aligned, the gear teeth need to bite into the filament. The gear could either be reversed...17 replies | 953 view(s)
-
01-28-2019, 05:09 PMI watched your video, it appears that your nozzle is still too high above the bed. Quick test you take a sheet of paper from your printer cut to the...17 replies | 953 view(s)
-
01-27-2019, 06:41 PMCura uses both the older versions use .ini the newer versions use .Curaprofile You can look at what I have and adjust what you need and create your...37 replies | 2081 view(s)
-
01-27-2019, 12:25 PMRoberts_Clif replied to a thread Sustainable solution: Auto-off-upon-finish Function: 3d Printer Auto-off Switchers in Free Self PromotionI have a raspberry Pi Running Octoprint, If I want only need to add a relay to control the AC Power on/off. I have never needed to use, did buy a...6 replies | 1301 view(s)
-
01-27-2019, 09:46 AMThis is most likely his speed percentage, In Cura 80% breaks down to about 9.0mm^3 per second. With a similar 3D Printer I can maintain a constant...5 replies | 486 view(s)
-
01-27-2019, 09:08 AMI have Ender 3 predecessors the 3DP11 and 3DP12, Almost no one was there for me to help weed thru all the learning process. Then I came across...37 replies | 2081 view(s)
-
01-27-2019, 09:06 AMWant my Cura Profiles for Hictop 3DP11/12 It appears you are getting under extrusion, your filament maybe getting tangled or you may have a...37 replies | 2081 view(s)
-
01-26-2019, 03:59 PMNO! You can only print about 80% the nozzle size for layer height. This would be .4 * 80% = .32mm Max Layer Height. I normally print between .2...37 replies | 2081 view(s)
-
01-26-2019, 12:30 PMI have profiles from 05 - 30 this is the layer height. What layer height are you using. I see you have Ender-3 PLA 1.75mm 200C...37 replies | 2081 view(s)
-
01-25-2019, 06:26 PMThen I do know have a clue of how to adjust your V-Ref. We were talking about Layer Shifting and I posted https://reprap.org/wiki/Shifted_layers...8 replies | 788 view(s)
-
01-25-2019, 11:12 AMNo V-Ref is a Controller voltage reference adjustment on the Stepper motor Driver module or Controller PCB. Warning Use lowest V-Ref Voltage...8 replies | 788 view(s)
-
01-23-2019, 08:43 PMIt appears that you are having a Layer shift. This is caused my a number of things Start here https://reprap.org/wiki/Shifted_layers After...8 replies | 788 view(s)
About Roberts_Clif
Basic Information
About Roberts_Clif
- Location:
- Washington State, USA
- Occupation:
- Electroncis Tech / IT / Programmer
- Thingiverse:
- Roberts_Clif
Statistics
Total Posts
- Total Posts
- 436
- Posts Per Day
- 0.71
General Information
- Last Activity
- Yesterday 03:49 PM
- Join Date
- 06-12-2017
- Referrals
- 0
New $139 Kossel Linear on ebay?!?
02-13-2019, 10:46 AM in 3D Printers (Hardware)