- Tab Content
- TTVert's Activity
- About Me
-
Older Activity
-
07-25-2022, 02:49 PMTTVert replied to a thread Duplicator i3, what are YOU doing for out of filament sensors? in General 3D Printing DiscussionWell that's helpful.. I did fabricate a mount for a switch and it works well. I just would really like to move that filament sensor to where it...2 replies | 826 view(s)
-
07-21-2022, 05:22 PMTTVert replied to a thread Interesting print "defect" that does not occur around the entire print in Tips, Tricks and Tech HelpI will give it a go, I've always been able to print at this speed/temp before w/o the issue. This spool of filament is about done but I'm curious if...2 replies | 806 view(s)
-
07-21-2022, 04:27 PMTTVert started a thread Interesting print "defect" that does not occur around the entire print in Tips, Tricks and Tech HelpThis is a round piece. Specs:The printer is a Duplicator i3+. I'm printing PLA (205C) Outer wall at 60mm/secInner at 80mm/sec.030mm layer height. ...2 replies | 806 view(s)
-
07-16-2022, 07:35 PMTTVert replied to a thread Fan only goes to 50% in code despite setting, feel i'm missing something in General 3D Printing DiscussionI do understand this. I am not explaining myself well i guess. My slicer should be slicing and varying fan speed and it is not. I do see only one...4 replies | 1129 view(s)
-
07-16-2022, 07:31 PMTTVert started a thread Duplicator i3, what are YOU doing for out of filament sensors? in General 3D Printing DiscussionI really wanted to be able to monitor out of filament at the extruder as i have had multiple occasions where my filament has broken closer to the...2 replies | 826 view(s)
-
07-15-2022, 12:29 PMTTVert replied to a thread Fan only goes to 50% in code despite setting, feel i'm missing something in General 3D Printing DiscussionThanks, i understand the code. For some reason my slicer is just not changing fan speed on prints i feel meet the criteria for full fan speed. IE i...4 replies | 1129 view(s)
-
07-14-2022, 04:27 PMTTVert replied to a thread Larger PETG part, extreme layer shifting (Over 50mm up and 20mm right) in Tips, Tricks and Tech HelpThis was a very short and wide print so it had tons of surface area to bond to the plate. It was PETG too which bonds to the point I can barely get...4 replies | 1117 view(s)
-
07-14-2022, 08:59 AMTTVert replied to a thread Larger PETG part, extreme layer shifting (Over 50mm up and 20mm right) in General 3D Printing DiscussionThank you, I had checked all mechanicals. I determined what had happened is during my first test print a bunch of excess ASA got between the...2 replies | 735 view(s)
-
07-13-2022, 09:10 PMTTVert started a thread Fan only goes to 50% in code despite setting, feel i'm missing something in General 3D Printing DiscussionI use repetier w/ the cura slicer engine for this. Looking at gcode I'm at 50% fan speed after layer 1 and then it turns off at completion. The...4 replies | 1129 view(s)
About TTVert
Basic Information
Statistics
Total Posts
- Total Posts
- 79
- Posts Per Day
- 0.04
General Information
- Last Activity
- 07-31-2022 11:24 AM
- Join Date
- 02-16-2017
I have some bsic questions
08-07-2022, 01:12 AM in General 3D Printing Discussion