Close



Page 1 of 4 123 ... LastLast
Threads 1 to 20 of 74

Forum: M3D Forum

Discussion related to the new M3D 3D printer

  1. Sticky Thread Sticky: The Micro 3D Backer Intro Thread

    Started by Eddie, 04-10-2014 07:23 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 21,060
    08-19-2016, 03:59 PM Go to last post
  1. Angry Can't get driver to install...

    Started by SlavaPHP, 01-12-2019 06:58 PM
    • Replies: 7
    • Views: 2,527
    01-13-2019, 02:44 PM Go to last post
  2. Thumbs up Calibtion Collision...

    Started by SlavaPHP, 01-13-2019 09:30 AM
    • Replies: 0
    • Views: 1,123
    01-13-2019, 09:30 AM Go to last post
  3. M3d software not opening Stl files

    Started by Bmrm145, 06-16-2018 12:53 AM
    • Replies: 0
    • Views: 1,564
    06-16-2018, 12:53 AM Go to last post
  4. Unhappy Uneven Test Border Extrusion

    Started by mpscaletti, 08-02-2016 05:37 PM
    • Replies: 2
    • Views: 6,295
    04-26-2018, 08:36 AM Go to last post
  5. Unhappy X-Rods not glued? Possible defect?

    Started by Cyber Akuma, 03-14-2018 12:41 PM
    • Replies: 1
    • Views: 1,994
    03-22-2018, 08:55 AM Go to last post
  6. My M3D Experience - Don't buy it!

    Started by hotrod1965, 11-17-2015 08:51 PM
    don't buy it, m3d
    • Replies: 4
    • Views: 9,217
    12-22-2016, 10:47 PM Go to last post
  7. best way to clean print?

    Started by chaotic1, 02-04-2016 10:49 PM
    clean-up, novice
    • Replies: 3
    • Views: 4,996
    11-13-2016, 08:04 PM Go to last post
  8. Question defect?

    Started by iIiastro4KiIi, 08-19-2016 03:37 PM
    m3d
    • Replies: 2
    • Views: 3,264
    11-13-2016, 08:02 PM Go to last post
  9. M3D CubePro - Temperature Issues

    Started by dasn25, 11-08-2016 02:49 PM
    cubepro, nozzle, temperature, trio
    • Replies: 0
    • Views: 2,839
    11-08-2016, 02:49 PM Go to last post
  10. M3D wont extrude

    Started by itspenutbutterjellytime, 10-22-2016 04:38 PM
    • Replies: 2
    • Views: 3,677
    10-26-2016, 11:06 AM Go to last post
  11. Can M3D be run using iPad?

    Started by chaotic1, 03-01-2016 08:51 PM
    ipad, tablet
    • Replies: 7
    • Views: 6,316
    08-19-2016, 03:39 PM Go to last post
  12. Poll Poll: Thinking about ordering. Is it actually good?

    Started by lcoopman, 03-13-2015 10:30 AM
    m3d
    • Replies: 7
    • Views: 7,735
    08-19-2016, 02:15 PM Go to last post
  13. Anyone tried to make a heated bed?

    Started by chaotic1, 02-27-2016 12:53 AM
    2 Pages
    1 2
    diy, heater
    • Replies: 10
    • Views: 7,597
    07-26-2016, 11:05 PM Go to last post
  14. Angry I really dont know why this is happening

    Started by TopherSays, 11-12-2015 09:24 PM
    • Replies: 3
    • Views: 4,661
    05-30-2016, 09:38 PM Go to last post
  15. Angry Losing Z height mid print

    Started by rhdwillis, 03-18-2016 08:55 PM
    m3d
    • Replies: 1
    • Views: 3,275
    03-19-2016, 07:15 PM Go to last post
  16. Question Tangled mess of filament

    Started by chaotic1, 02-25-2016 07:30 PM
    • Replies: 3
    • Views: 4,429
    02-27-2016, 12:33 AM Go to last post
  17. The end of my printer (catastrophic failure)

    Started by Duck, 08-15-2015 06:03 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 11,050
    02-26-2016, 07:20 PM Go to last post
  18. M3D Printer

    Started by parkbobo, 12-20-2015 11:10 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 10,551
    02-13-2016, 01:26 AM Go to last post
  19. Learning to design in 3D

    Started by chaotic1, 02-04-2016 11:41 PM
    3dimension, design, lessons, programs
    • Replies: 7
    • Views: 5,317
    02-12-2016, 02:35 AM Go to last post
  20. new to 3D printing, help please

    Started by DaleSabers, 11-01-2015 09:21 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 10,930
    02-09-2016, 03:28 PM Go to last post

Page 1 of 4 123 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •