Close



Page 1 of 4 123 ... LastLast
Threads 1 to 20 of 74

Forum: M3D Forum

Discussion related to the new M3D 3D printer

  1. Sticky Thread Sticky: The Micro 3D Backer Intro Thread

    Started by Eddie, 04-10-2014 07:23 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 67,549
    08-19-2016, 03:59 PM Go to last post
  1. Anyone tried to make a heated bed?

    Started by chaotic1, 02-27-2016 12:53 AM
    2 Pages
    1 2
    diy, heater
    • Replies: 10
    • Views: 49,263
    07-26-2016, 11:05 PM Go to last post
  2. M3D Printer

    Started by parkbobo, 12-20-2015 11:10 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 47,071
    02-13-2016, 01:26 AM Go to last post
  3. new to 3D printing, help please

    Started by DaleSabers, 11-01-2015 09:21 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 46,674
    02-09-2016, 03:28 PM Go to last post
  4. The end of my printer (catastrophic failure)

    Started by Duck, 08-15-2015 06:03 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 43,536
    02-26-2016, 07:20 PM Go to last post
  5. Angry Can't get driver to install...

    Started by SlavaPHP, 01-12-2019 06:58 PM
    • Replies: 7
    • Views: 39,942
    01-13-2019, 02:44 PM Go to last post
  6. Poll Poll: Thinking about ordering. Is it actually good?

    Started by lcoopman, 03-13-2015 10:30 AM
    m3d
    • Replies: 7
    • Views: 33,482
    08-19-2016, 02:15 PM Go to last post
  7. Getting close to initial KS awards

    Started by WayTooManyHobbies, 09-15-2014 10:41 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 31,352
    11-22-2014, 02:05 PM Go to last post
  8. Can M3D be run using iPad?

    Started by chaotic1, 03-01-2016 08:51 PM
    ipad, tablet
    • Replies: 7
    • Views: 28,847
    08-19-2016, 03:39 PM Go to last post
  9. Learning to design in 3D

    Started by chaotic1, 02-04-2016 11:41 PM
    3dimension, design, lessons, programs
    • Replies: 7
    • Views: 27,832
    02-12-2016, 02:35 AM Go to last post
  10. My M3D Experience - Don't buy it!

    Started by hotrod1965, 11-17-2015 08:51 PM
    don't buy it, m3d
    • Replies: 4
    • Views: 27,308
    12-22-2016, 10:47 PM Go to last post
  11. Pre-ordering the Micro3d?

    Started by JacobysOne, 05-30-2014 11:33 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 26,715
    06-10-2015, 08:10 PM Go to last post
  12. best way to clean print?

    Started by chaotic1, 02-04-2016 10:49 PM
    clean-up, novice
    • Replies: 3
    • Views: 25,190
    11-13-2016, 08:04 PM Go to last post
  13. Unhappy Uneven Test Border Extrusion

    Started by mpscaletti, 08-02-2016 05:37 PM
    • Replies: 2
    • Views: 24,892
    04-26-2018, 08:36 AM Go to last post
  14. Question defect?

    Started by iIiastro4KiIi, 08-19-2016 03:37 PM
    m3d
    • Replies: 2
    • Views: 24,775
    11-13-2016, 08:02 PM Go to last post
  15. Thumbs up Calibtion Collision...

    Started by SlavaPHP, 01-13-2019 09:30 AM
    • Replies: 0
    • Views: 23,449
    01-13-2019, 09:30 AM Go to last post
  16. Angry I really dont know why this is happening

    Started by TopherSays, 11-12-2015 09:24 PM
    • Replies: 3
    • Views: 23,038
    05-30-2016, 09:38 PM Go to last post
  17. Question Tangled mess of filament

    Started by chaotic1, 02-25-2016 07:30 PM
    • Replies: 3
    • Views: 22,266
    02-27-2016, 12:33 AM Go to last post
  18. M3D wont extrude

    Started by itspenutbutterjellytime, 10-22-2016 04:38 PM
    • Replies: 2
    • Views: 21,544
    10-26-2016, 11:06 AM Go to last post
  19. The micro. New video. 3dp tests

    Started by icanthinkofanid, 01-23-2015 08:35 PM
    2 Pages
    1 2
    • Replies: 18
    • Views: 21,339
    02-01-2015, 12:51 PM Go to last post
  20. New 3D Printer Owner/M3D Micro

    Started by TheBigCreator, 04-28-2015 08:27 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 20,386
    08-11-2015, 07:52 AM Go to last post

Page 1 of 4 123 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data