Close



Page 1 of 4 123 ... LastLast
Threads 1 to 20 of 72

Forum: M3D Forum

Discussion related to the new M3D 3D printer

  1. Sticky Thread Sticky: The Micro 3D Backer Intro Thread

    Started by Eddie, 04-10-2014 08:23 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 18,466
    08-19-2016, 04:59 PM Go to last post
  1. M3d software not opening Stl files

    Started by Bmrm145, 06-16-2018 01:53 AM
    • Replies: 0
    • Views: 1,197
    06-16-2018, 01:53 AM Go to last post
  2. Unhappy Uneven Test Border Extrusion

    Started by mpscaletti, 08-02-2016 06:37 PM
    • Replies: 2
    • Views: 5,468
    04-26-2018, 09:36 AM Go to last post
  3. Unhappy X-Rods not glued? Possible defect?

    Started by Cyber Akuma, 03-14-2018 01:41 PM
    • Replies: 1
    • Views: 1,297
    03-22-2018, 09:55 AM Go to last post
  4. My M3D Experience - Don't buy it!

    Started by hotrod1965, 11-17-2015 09:51 PM
    don't buy it, m3d
    • Replies: 4
    • Views: 8,263
    12-22-2016, 11:47 PM Go to last post
  5. best way to clean print?

    Started by chaotic1, 02-04-2016 11:49 PM
    clean-up, novice
    • Replies: 3
    • Views: 4,025
    11-13-2016, 09:04 PM Go to last post
  6. Question defect?

    Started by iIiastro4KiIi, 08-19-2016 04:37 PM
    m3d
    • Replies: 2
    • Views: 2,542
    11-13-2016, 09:02 PM Go to last post
  7. M3D CubePro - Temperature Issues

    Started by dasn25, 11-08-2016 03:49 PM
    cubepro, nozzle, temperature, trio
    • Replies: 0
    • Views: 2,164
    11-08-2016, 03:49 PM Go to last post
  8. M3D wont extrude

    Started by itspenutbutterjellytime, 10-22-2016 05:38 PM
    • Replies: 2
    • Views: 2,982
    10-26-2016, 12:06 PM Go to last post
  9. Can M3D be run using iPad?

    Started by chaotic1, 03-01-2016 09:51 PM
    ipad, tablet
    • Replies: 7
    • Views: 5,287
    08-19-2016, 04:39 PM Go to last post
  10. Poll Poll: Thinking about ordering. Is it actually good?

    Started by lcoopman, 03-13-2015 11:30 AM
    m3d
    • Replies: 7
    • Views: 6,755
    08-19-2016, 03:15 PM Go to last post
  11. Anyone tried to make a heated bed?

    Started by chaotic1, 02-27-2016 01:53 AM
    2 Pages
    1 2
    diy, heater
    • Replies: 10
    • Views: 6,264
    07-27-2016, 12:05 AM Go to last post
  12. Angry I really dont know why this is happening

    Started by TopherSays, 11-12-2015 10:24 PM
    • Replies: 3
    • Views: 3,764
    05-30-2016, 10:38 PM Go to last post
  13. Angry Losing Z height mid print

    Started by rhdwillis, 03-18-2016 09:55 PM
    m3d
    • Replies: 1
    • Views: 2,484
    03-19-2016, 08:15 PM Go to last post
  14. Question Tangled mess of filament

    Started by chaotic1, 02-25-2016 08:30 PM
    • Replies: 3
    • Views: 3,451
    02-27-2016, 01:33 AM Go to last post
  15. The end of my printer (catastrophic failure)

    Started by Duck, 08-15-2015 07:03 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 9,436
    02-26-2016, 08:20 PM Go to last post
  16. M3D Printer

    Started by parkbobo, 12-21-2015 12:10 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 8,841
    02-13-2016, 02:26 AM Go to last post
  17. Learning to design in 3D

    Started by chaotic1, 02-05-2016 12:41 AM
    3dimension, design, lessons, programs
    • Replies: 7
    • Views: 4,327
    02-12-2016, 03:35 AM Go to last post
  18. new to 3D printing, help please

    Started by DaleSabers, 11-01-2015 10:21 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 9,152
    02-09-2016, 04:28 PM Go to last post
  19. Printer won't extrude/release ink

    Started by MechaMew2, 09-02-2015 03:27 PM
    • Replies: 5
    • Views: 5,324
    01-25-2016, 05:04 PM Go to last post
  20. New to M3D - minor issue with prints offset

    Started by Rich M, 12-27-2015 07:55 AM
    • Replies: 2
    • Views: 3,432
    01-24-2016, 12:26 PM Go to last post

Page 1 of 4 123 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •