Close



Page 1 of 54 1231151 ... LastLast
Threads 1 to 20 of 1065

Forum: 3D Printer Parts, Filament & Materials

Discussion related to 3D Printer parts, such as hot ends, extruders, and anything else you may want to discuss related to printer parts, as well as filament, resin, and sintering powder.

    • Replies: 12
    • Views: 17,416
    01-27-2020, 01:41 AM Go to last post
  1. Sticky Thread Sticky: Anyone used Printbite surface ?

    Started by curious aardvark, 03-15-2016 07:56 AM
    10 Pages
    1 2 3 ... 10
    • Replies: 94
    • Views: 90,032
    07-30-2019, 01:49 AM Go to last post
  2. Sticky Thread Sticky: Message for filament manufacturers !!!

    Started by curious aardvark, 12-31-2018 07:59 AM
    • Replies: 0
    • Views: 3,922
    12-31-2018, 07:59 AM Go to last post
  1. Storing Filament in a Brisker

    Started by panamajuice, 09-09-2018 10:45 PM
    • Replies: 3
    • Views: 1,887
    Today, 02:48 PM Go to last post
  2. Question about printing ABS with USM

    Started by FlacOrGtfo, 06-27-2019 12:00 PM
    abs, material, support, usm
    • Replies: 5
    • Views: 1,534
    Today, 01:48 PM Go to last post
  3. Warping while printing PEEK

    Started by LeglessPooch, 01-21-2020 01:54 PM
    • Replies: 4
    • Views: 320
    Yesterday, 06:59 AM Go to last post
  4. U10 replacement parts

    Started by magyaripatrick, 01-23-2020 07:18 PM
    • Replies: 0
    • Views: 242
    01-23-2020, 07:18 PM Go to last post
  5. U10 replacement parts (selector button)

    Started by magyaripatrick, 01-07-2020 10:45 PM
    • Replies: 3
    • Views: 481
    01-23-2020, 04:20 PM Go to last post
  6. 101hero hot end only heat to 89 degrees!

    Started by noodlesnoah, 01-23-2020 03:01 AM
    • Replies: 0
    • Views: 144
    01-23-2020, 03:01 AM Go to last post
  7. Bed will not stick on one side

    Started by Bruce19, 01-20-2020 03:40 PM
    • Replies: 2
    • Views: 182
    01-21-2020, 06:22 PM Go to last post
    • Replies: 5
    • Views: 558
    01-21-2020, 07:52 AM Go to last post
  8. A good cheap projector for DLP SLA?

    Started by patreojames, 11-27-2014 01:01 PM
    • Replies: 1
    • Views: 1,027
    01-20-2020, 07:25 AM Go to last post
    • Replies: 1
    • Views: 223
    01-13-2020, 10:25 AM Go to last post
  9. Just need info about this Hotbed Connector type

    Started by hynostroza, 01-12-2020 06:57 PM
    • Replies: 0
    • Views: 240
    01-12-2020, 06:57 PM Go to last post
  10. PETG: I'm not sure what I'm looking at

    Started by piotr1990, 12-31-2019 04:13 PM
    • Replies: 1
    • Views: 477
    01-06-2020, 08:40 AM Go to last post
  11. Lightbulb Tool for Finding Printing Tolerances

    Started by Saccade, 01-01-2020 02:38 PM
    • Replies: 1
    • Views: 399
    01-01-2020, 03:56 PM Go to last post
  12. heated bed issue

    Started by heizer, 12-20-2019 10:35 AM
    • Replies: 4
    • Views: 907
    12-24-2019, 11:15 PM Go to last post
  13. Resin question

    Started by mwieting, 12-24-2019 03:46 PM
    • Replies: 0
    • Views: 329
    12-24-2019, 03:46 PM Go to last post
    • Replies: 2
    • Views: 706
    12-17-2019, 07:49 AM Go to last post
    • Replies: 2
    • Views: 665
    12-09-2019, 12:55 PM Go to last post
  14. Filament Recycling

    Started by goose, 10-22-2019 03:37 PM
    • Replies: 1
    • Views: 1,140
    12-09-2019, 12:52 PM Go to last post
    • Replies: 2
    • Views: 672
    12-08-2019, 10:10 PM Go to last post
    • Replies: 1
    • Views: 497
    12-05-2019, 02:40 PM Go to last post

Page 1 of 54 1231151 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data