Close



Page 1 of 54 1231151 ... LastLast
Threads 1 to 20 of 1071

Forum: 3D Printer Parts, Filament & Materials

Discussion related to 3D Printer parts, such as hot ends, extruders, and anything else you may want to discuss related to printer parts, as well as filament, resin, and sintering powder.

    • Replies: 12
    • Views: 17,989
    01-27-2020, 01:41 AM Go to last post
  1. Sticky Thread Sticky: Anyone used Printbite surface ?

    Started by curious aardvark, 03-15-2016 07:56 AM
    10 Pages
    1 2 3 ... 10
    • Replies: 94
    • Views: 91,577
    07-30-2019, 01:49 AM Go to last post
  2. Sticky Thread Sticky: Message for filament manufacturers !!!

    Started by curious aardvark, 12-31-2018 07:59 AM
    • Replies: 0
    • Views: 4,147
    12-31-2018, 07:59 AM Go to last post
  1. Warping while printing PEEK

    Started by LeglessPooch, 01-21-2020 01:54 PM
    • Replies: 6
    • Views: 773
    Today, 05:57 AM Go to last post
  2. Sell Filament?

    Started by a_zyci, 02-18-2020 11:34 AM
    filament, mark, markforged, onyx, sell
    • Replies: 3
    • Views: 158
    02-18-2020, 03:38 PM Go to last post
    • Replies: 2
    • Views: 371
    02-14-2020, 11:26 AM Go to last post
  3. Question Zortrax M200-Pythone Flex

    Started by jugrina, 02-05-2020 09:17 AM
    zortrax
    • Replies: 5
    • Views: 635
    02-12-2020, 03:47 AM Go to last post
  4. Beginner - Parts for Makerbot Replicator 2

    Started by jsaunders, 02-04-2020 03:12 PM
    • Replies: 1
    • Views: 227
    02-05-2020, 07:02 AM Go to last post
  5. A good cheap projector for DLP SLA?

    Started by patreojames, 11-27-2014 01:01 PM
    • Replies: 2
    • Views: 1,259
    02-04-2020, 07:59 AM Go to last post
  6. Is aluminum 7075 printable?

    Started by Spannbacken, 02-01-2020 05:03 AM
    aluminium printing, spannbacken
    • Replies: 2
    • Views: 347
    02-04-2020, 02:10 AM Go to last post
  7. Difficulty Staining PLA Wood Filament

    Started by bzowk, 01-29-2020 07:31 PM
    • Replies: 5
    • Views: 506
    02-03-2020, 10:46 AM Go to last post
  8. ESD safe Flexible filament?

    Started by Scott Printer, 10-06-2017 01:53 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 6,780
    01-30-2020, 01:45 PM Go to last post
  9. Storing Filament in a Brisker

    Started by panamajuice, 09-09-2018 10:45 PM
    • Replies: 3
    • Views: 2,213
    01-29-2020, 02:48 PM Go to last post
  10. Question about printing ABS with USM

    Started by FlacOrGtfo, 06-27-2019 12:00 PM
    abs, material, support, usm
    • Replies: 5
    • Views: 1,787
    01-29-2020, 01:48 PM Go to last post
  11. U10 replacement parts

    Started by magyaripatrick, 01-23-2020 07:18 PM
    • Replies: 0
    • Views: 506
    01-23-2020, 07:18 PM Go to last post
  12. U10 replacement parts (selector button)

    Started by magyaripatrick, 01-07-2020 10:45 PM
    • Replies: 3
    • Views: 721
    01-23-2020, 04:20 PM Go to last post
  13. 101hero hot end only heat to 89 degrees!

    Started by noodlesnoah, 01-23-2020 03:01 AM
    • Replies: 0
    • Views: 315
    01-23-2020, 03:01 AM Go to last post
  14. Bed will not stick on one side

    Started by Bruce19, 01-20-2020 03:40 PM
    • Replies: 2
    • Views: 327
    01-21-2020, 06:22 PM Go to last post
    • Replies: 5
    • Views: 803
    01-21-2020, 07:52 AM Go to last post
    • Replies: 1
    • Views: 366
    01-13-2020, 10:25 AM Go to last post
  15. Just need info about this Hotbed Connector type

    Started by hynostroza, 01-12-2020 06:57 PM
    • Replies: 0
    • Views: 397
    01-12-2020, 06:57 PM Go to last post
  16. PETG: I'm not sure what I'm looking at

    Started by piotr1990, 12-31-2019 04:13 PM
    • Replies: 1
    • Views: 617
    01-06-2020, 08:40 AM Go to last post
  17. Lightbulb Tool for Finding Printing Tolerances

    Started by Saccade, 01-01-2020 02:38 PM
    • Replies: 1
    • Views: 539
    01-01-2020, 03:56 PM Go to last post

Page 1 of 54 1231151 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data