Close



Page 1 of 54 1231151 ... LastLast
Threads 1 to 20 of 1072

Forum: 3D Printer Parts, Filament & Materials

Discussion related to 3D Printer parts, such as hot ends, extruders, and anything else you may want to discuss related to printer parts, as well as filament, resin, and sintering powder.

    • Replies: 12
    • Views: 18,224
    01-27-2020, 01:41 AM Go to last post
  1. Sticky Thread Sticky: Anyone used Printbite surface ?

    Started by curious aardvark, 03-15-2016 07:56 AM
    10 Pages
    1 2 3 ... 10
    • Replies: 94
    • Views: 92,202
    07-30-2019, 01:49 AM Go to last post
  2. Sticky Thread Sticky: Message for filament manufacturers !!!

    Started by curious aardvark, 12-31-2018 07:59 AM
    • Replies: 0
    • Views: 4,254
    12-31-2018, 07:59 AM Go to last post
  1. polysmoth transparent bad print

    Started by piotr1990, 02-23-2020 05:31 AM
    • Replies: 2
    • Views: 248
    02-25-2020, 05:12 PM Go to last post
  2. Warping while printing PEEK

    Started by LeglessPooch, 01-21-2020 01:54 PM
    • Replies: 6
    • Views: 1,080
    02-20-2020, 05:57 AM Go to last post
  3. Sell Filament?

    Started by a_zyci, 02-18-2020 11:34 AM
    filament, mark, markforged, onyx, sell
    • Replies: 3
    • Views: 310
    02-18-2020, 03:38 PM Go to last post
    • Replies: 2
    • Views: 516
    02-14-2020, 11:26 AM Go to last post
  4. Question Zortrax M200-Pythone Flex

    Started by jugrina, 02-05-2020 09:17 AM
    zortrax
    • Replies: 5
    • Views: 846
    02-12-2020, 03:47 AM Go to last post
  5. Beginner - Parts for Makerbot Replicator 2

    Started by jsaunders, 02-04-2020 03:12 PM
    • Replies: 1
    • Views: 342
    02-05-2020, 07:02 AM Go to last post
  6. A good cheap projector for DLP SLA?

    Started by patreojames, 11-27-2014 01:01 PM
    • Replies: 2
    • Views: 1,353
    02-04-2020, 07:59 AM Go to last post
  7. Is aluminum 7075 printable?

    Started by Spannbacken, 02-01-2020 05:03 AM
    aluminium printing, spannbacken
    • Replies: 2
    • Views: 451
    02-04-2020, 02:10 AM Go to last post
  8. Difficulty Staining PLA Wood Filament

    Started by bzowk, 01-29-2020 07:31 PM
    • Replies: 5
    • Views: 663
    02-03-2020, 10:46 AM Go to last post
  9. ESD safe Flexible filament?

    Started by Scott Printer, 10-06-2017 01:53 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 7,008
    01-30-2020, 01:45 PM Go to last post
  10. Storing Filament in a Brisker

    Started by panamajuice, 09-09-2018 10:45 PM
    • Replies: 3
    • Views: 2,344
    01-29-2020, 02:48 PM Go to last post
  11. Question about printing ABS with USM

    Started by FlacOrGtfo, 06-27-2019 12:00 PM
    abs, material, support, usm
    • Replies: 5
    • Views: 1,908
    01-29-2020, 01:48 PM Go to last post
  12. U10 replacement parts

    Started by magyaripatrick, 01-23-2020 07:18 PM
    • Replies: 0
    • Views: 588
    01-23-2020, 07:18 PM Go to last post
  13. U10 replacement parts (selector button)

    Started by magyaripatrick, 01-07-2020 10:45 PM
    • Replies: 3
    • Views: 826
    01-23-2020, 04:20 PM Go to last post
  14. 101hero hot end only heat to 89 degrees!

    Started by noodlesnoah, 01-23-2020 03:01 AM
    • Replies: 0
    • Views: 389
    01-23-2020, 03:01 AM Go to last post
  15. Bed will not stick on one side

    Started by Bruce19, 01-20-2020 03:40 PM
    • Replies: 2
    • Views: 418
    01-21-2020, 06:22 PM Go to last post
    • Replies: 5
    • Views: 921
    01-21-2020, 07:52 AM Go to last post
    • Replies: 1
    • Views: 447
    01-13-2020, 10:25 AM Go to last post
  16. Just need info about this Hotbed Connector type

    Started by hynostroza, 01-12-2020 06:57 PM
    • Replies: 0
    • Views: 483
    01-12-2020, 06:57 PM Go to last post
  17. PETG: I'm not sure what I'm looking at

    Started by piotr1990, 12-31-2019 04:13 PM
    • Replies: 1
    • Views: 710
    01-06-2020, 08:40 AM Go to last post

Page 1 of 54 1231151 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data