Close
Flash Forge Inventor II Spring Promotion



Page 58 of 60 FirstFirst ... 8485657585960 LastLast
Threads 1141 to 1160 of 1191

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 07:48 AM
    3 Pages
    1 2 3
    • Replies: 27
    • Views: 4,840
    03-07-2018, 04:09 PM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 57,115
    08-12-2016, 11:26 AM Go to last post
  1. How to Calibrate a 3D Printer Extruder

    Started by EveryDayIDream, 04-06-2014 07:26 AM
    • Replies: 1
    • Views: 2,771
    04-06-2014, 10:39 AM Go to last post
  2. 3D printer prints warped objects

    Started by BikeRide, 03-30-2014 01:37 PM
    • Replies: 3
    • Views: 1,187
    04-01-2014, 07:11 AM Go to last post
  3. What could be causing these problems?

    Started by Ka50, 03-23-2014 10:28 AM
    • Replies: 7
    • Views: 2,357
    03-30-2014, 05:08 PM Go to last post
  4. Pronterface install problem

    Started by old man emu, 03-27-2014 02:45 AM
    • Replies: 4
    • Views: 7,217
    03-30-2014, 08:28 AM Go to last post
  5. Getting down and dirty with Slic3r

    Started by old man emu, 03-26-2014 02:09 AM
    • Replies: 1
    • Views: 1,116
    03-28-2014, 07:29 AM Go to last post
  6. Question Printing with Wood Filament & Final Finishes

    Started by jssnoopy, 03-25-2014 11:51 PM
    • Replies: 6
    • Views: 1,716
    03-27-2014, 01:48 PM Go to last post
  7. Hot end Prusia i3

    Started by Creted3d, 03-17-2014 06:34 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 5,578
    03-26-2014, 08:31 PM Go to last post
  8. How to set up endstop switches.

    Started by old man emu, 03-13-2014 07:04 AM
    • Replies: 3
    • Views: 1,571
    03-26-2014, 06:30 PM Go to last post
  9. Reducing materials used during a 3D print

    Started by squadus, 03-19-2014 03:46 PM
    • Replies: 2
    • Views: 993
    03-26-2014, 06:21 PM Go to last post
  10. Measuring RAMPS Board Stepper Motor Voltage

    Started by old man emu, 03-24-2014 08:19 PM
    • Replies: 2
    • Views: 3,952
    03-25-2014, 07:07 PM Go to last post
  11. Possible to print with no lines with FDM

    Started by pathfindr, 03-23-2014 10:15 AM
    • Replies: 2
    • Views: 1,080
    03-24-2014, 07:56 AM Go to last post
    • Replies: 5
    • Views: 1,245
    03-23-2014, 10:49 AM Go to last post
  12. Need some Firmware help

    Started by Vonnely, 03-20-2014 02:38 PM
    • Replies: 3
    • Views: 1,171
    03-21-2014, 06:28 PM Go to last post
  13. Best "Statue Looking" Filament?

    Started by QuitNoMore, 03-17-2014 03:27 PM
    • Replies: 1
    • Views: 2,145
    03-21-2014, 06:36 AM Go to last post
  14. Cleaning your printers?

    Started by RimReaping, 03-16-2014 09:08 AM
    • Replies: 5
    • Views: 2,037
    03-20-2014, 10:03 AM Go to last post
    • Replies: 1
    • Views: 864
    03-17-2014, 05:08 PM Go to last post
  15. Is it possible to 3d print a chain-like structure?

    Started by pardonme, 02-17-2014 05:40 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 7,057
    03-17-2014, 10:48 AM Go to last post
  16. Question Key Printing Temperatures

    Started by jssnoopy, 03-07-2014 12:15 AM
    printing temperature
    • Replies: 4
    • Views: 1,445
    03-15-2014, 03:13 PM Go to last post
  17. How is this 3d Printed? Slinkies

    Started by 3D_is_my_LIFE, 03-10-2014 08:41 AM
    • Replies: 9
    • Views: 2,646
    03-13-2014, 10:07 PM Go to last post
  18. Cleaning the bed in aceton

    Started by rene1981, 03-01-2014 02:27 PM
    • Replies: 4
    • Views: 1,479
    03-11-2014, 09:08 PM Go to last post

Page 58 of 60 FirstFirst ... 8485657585960 LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •