Close



Page 1 of 92 1231151 ... LastLast
Threads 1 to 20 of 1831

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 07:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 33,209
    01-20-2020, 10:03 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 69
    • Views: 95,341
    02-29-2020, 08:28 PM Go to last post
    • Replies: 0
    • Views: 1,536
    10-31-2015, 11:56 AM Go to last post
    • Replies: 0
    • Views: 1,973
    06-07-2015, 07:11 AM Go to last post
  1. "shark gills" printing ugh! creality cr-10s

    Started by grue, 02-07-2018 06:00 PM
    • Replies: 7
    • Views: 2,303
    02-08-2018, 04:34 PM Go to last post
  2. "Stepped" Prints - Take a Look

    Started by Phantom462, 12-21-2019 11:00 AM
    • Replies: 2
    • Views: 555
    12-21-2019, 02:06 PM Go to last post
  3. "Threaded" prints (picture inside)

    Started by Decoy, 11-06-2019 02:26 PM
    • Replies: 2
    • Views: 799
    11-07-2019, 02:24 PM Go to last post
  4. Exclamation "Wait for User" - Creality CR-10 S5 Error

    Started by Kairiwolfart, 04-18-2019 04:50 PM
    3dprinter, creality, error, firmware
    • Replies: 0
    • Views: 1,106
    04-18-2019, 04:50 PM Go to last post
  5. (Trick) Reusing limonene

    Started by hamster, 03-26-2015 10:28 AM
    • Replies: 0
    • Views: 1,778
    03-26-2015, 10:28 AM Go to last post
    • Replies: 5
    • Views: 800
    05-17-2020, 11:26 PM Go to last post
  6. .8 mm too big!

    Started by Perry, 07-12-2014 11:57 PM
    • Replies: 1
    • Views: 1,545
    07-13-2014, 05:20 AM Go to last post
  7. .8 nozzle troubleshooting

    Started by Alegence, 02-28-2017 06:32 PM
    • Replies: 1
    • Views: 1,700
    02-28-2017, 06:36 PM Go to last post
  8. 1st and even 2nd layer not sticking

    Started by jeromego, 01-14-2019 05:11 AM
    • Replies: 0
    • Views: 543
    01-14-2019, 05:11 AM Go to last post
  9. 1st Layer

    Started by Gramps50, 04-19-2018 11:23 AM
    • Replies: 6
    • Views: 2,097
    04-21-2018, 08:32 PM Go to last post
    • Replies: 6
    • Views: 2,433
    08-15-2016, 09:20 PM Go to last post
  10. 1st layer wavy

    Started by Huxta, 06-17-2019 10:17 AM
    • Replies: 3
    • Views: 1,261
    07-23-2019, 06:23 PM Go to last post
  11. 2 40mm fans at once with one printrboard?

    Started by JamesTuthill, 05-14-2014 08:43 AM
    • Replies: 2
    • Views: 2,346
    05-14-2014, 11:27 AM Go to last post
  12. 2 Used Anycubic I3 mega printers in need of help.

    Started by MegasXLR, 07-06-2019 09:59 AM
    anycubic i3, help i'm new, not working
    • Replies: 0
    • Views: 1,000
    07-06-2019, 09:59 AM Go to last post
  13. 20mm test problem

    Started by gblass1, 06-11-2018 09:41 PM
    • Replies: 2
    • Views: 1,875
    06-14-2018, 10:13 AM Go to last post
  14. Question 20x20x10mm Calibration Question - Z18

    Started by WireframeFX, 05-12-2016 07:23 AM
    calibration, cube, makerbot desktop, makerbot replicator z18, z18
    • Replies: 4
    • Views: 2,709
    06-06-2016, 09:03 AM Go to last post
  15. 2d gcode?

    Started by Marm, 11-24-2015 08:48 AM
    • Replies: 3
    • Views: 1,156
    11-24-2015, 10:25 AM Go to last post
  16. Lightbulb 3 D printer problems i have had and sorted

    Started by 01012k7, 05-08-2016 03:07 AM
    • Replies: 0
    • Views: 1,353
    05-08-2016, 03:07 AM Go to last post

Page 1 of 92 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data