Close



Page 1 of 95 1231151 ... LastLast
Threads 1 to 20 of 1896

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 69
    • Views: 101,884
    02-29-2020, 08:28 PM Go to last post
  2. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 07:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 37,017
    01-20-2020, 10:03 AM Go to last post
  1. Newb needs Ender 3 Support

    Started by Dtech, 07-12-2019 12:03 PM
    ender 3; help; support
    • Replies: 4
    • Views: 1,715
    Today, 04:33 AM Go to last post
  2. DLP printing similar to photo-etching

    Started by San, 10-12-2020 05:02 PM
    dlp 3d printer, photo-etching
    • Replies: 8
    • Views: 517
    Yesterday, 12:08 PM Go to last post
  3. i need help badly

    Started by crazymonke42, 10-22-2020 04:24 PM
    • Replies: 3
    • Views: 217
    10-24-2020, 06:41 AM Go to last post
  4. Slight Gaps

    Started by 88Zombies, 10-07-2020 05:33 AM
    • Replies: 6
    • Views: 478
    10-23-2020, 02:33 PM Go to last post
    • Replies: 2
    • Views: 174
    10-22-2020, 06:37 PM Go to last post
  5. PLA doesn't print well on Ender 3 Pro, using Cura

    Started by dup, 10-19-2020 05:02 AM
    2 Pages
    1 2
    creality, ender 3 pro, pla, troubleshooting
    • Replies: 11
    • Views: 1,814
    10-22-2020, 02:18 PM Go to last post
  6. correct Z-offset is too low

    Started by reach, 10-13-2020 04:21 PM
    • Replies: 2
    • Views: 299
    10-20-2020, 06:09 AM Go to last post
  7. Question AnyCubic Delta Kossel Nozzle jam problem

    Started by HomaUn, 10-17-2020 05:55 PM
    • Replies: 1
    • Views: 309
    10-20-2020, 06:01 AM Go to last post
  8. CreatBot DX3 Mod

    Started by Mike70515, 10-15-2020 09:40 AM
    • Replies: 2
    • Views: 352
    10-15-2020, 02:04 PM Go to last post
  9. Ender 3: PLA Jams Constantly

    Started by YellowGTM, 08-26-2020 01:42 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 1,946
    10-14-2020, 11:44 AM Go to last post
  10. Object format question

    Started by carllwyman, 04-12-2018 02:44 AM
    • Replies: 1
    • Views: 1,236
    10-13-2020, 08:38 AM Go to last post
  11. Fail to make the printings fit to each other.

    Started by kostbill, 10-11-2020 04:33 PM
    • Replies: 5
    • Views: 800
    10-12-2020, 06:50 PM Go to last post
  12. Thermal Runaway E1

    Started by Ramblin' Sid Rumpo, 10-12-2020 03:02 AM
    • Replies: 0
    • Views: 286
    10-12-2020, 03:02 AM Go to last post
  13. noob needing help with ender 5 plus not printing

    Started by kaschwing, 10-11-2020 09:16 AM
    • Replies: 0
    • Views: 288
    10-11-2020, 09:16 AM Go to last post
  14. Unsmooth, harsh resolution

    Started by danmih83, 10-06-2020 01:04 PM
    • Replies: 3
    • Views: 444
    10-10-2020, 02:59 AM Go to last post
  15. Is really as good as they say?

    Started by ssear, 10-08-2020 03:27 AM
    • Replies: 1
    • Views: 394
    10-08-2020, 05:09 PM Go to last post
    • Replies: 5
    • Views: 656
    10-07-2020, 01:29 AM Go to last post
  16. CR10s constantly pausing

    Started by KPCx585, 10-05-2020 01:29 PM
    cr10s, cura, new to 3d, problem
    • Replies: 1
    • Views: 416
    10-06-2020, 06:24 AM Go to last post
  17. Good adhesion except one corner

    Started by DeathsmileZ, 10-02-2020 08:04 PM
    • Replies: 1
    • Views: 406
    10-04-2020, 10:31 AM Go to last post

Page 1 of 95 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data