Close



Page 1 of 81 1231151 ... LastLast
Threads 1 to 20 of 1601

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 08:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 23,497
    10-08-2018, 04:28 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 05:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 80,804
    08-12-2016, 12:26 PM Go to last post
    • Replies: 2
    • Views: 190
    01-16-2020, 02:54 PM Go to last post
  1. Angry Bad first layer need help.

    Started by gab, 01-16-2020 12:55 PM
    tevo tarantula pro
    • Replies: 0
    • Views: 67
    01-16-2020, 12:55 PM Go to last post
  2. Stop printing (Ender 3)

    Started by LupaShiva, 12-22-2019 05:10 AM
    • Replies: 3
    • Views: 405
    01-16-2020, 01:26 AM Go to last post
  3. [Problem] Ender 3 curling and not sticking to bed

    Started by notroy, 01-16-2020 12:00 AM
    • Replies: 0
    • Views: 87
    01-16-2020, 12:00 AM Go to last post
    • Replies: 8
    • Views: 491
    01-15-2020, 05:40 PM Go to last post
  4. Only one filament works

    Started by Marchello, 12-25-2019 10:09 PM
    • Replies: 3
    • Views: 266
    01-15-2020, 04:40 PM Go to last post
    • Replies: 2
    • Views: 181
    01-12-2020, 08:26 AM Go to last post
  5. Few beginner questions..

    Started by Shieldbreaker, 01-08-2020 10:07 AM
    • Replies: 2
    • Views: 240
    01-10-2020, 08:46 AM Go to last post
  6. Makerbot Replicator 2x z-axis calibration

    Started by theycallmevirgo, 01-09-2020 07:32 PM
    • Replies: 0
    • Views: 160
    01-09-2020, 07:32 PM Go to last post
  7. Issue With Prints

    Started by woodk405, 01-09-2020 04:04 PM
    • Replies: 0
    • Views: 198
    01-09-2020, 04:04 PM Go to last post
  8. CTC DOY Printer setup help - adjusting Z-position

    Started by Peterm7, 01-09-2020 02:42 PM
    ctc3d
    • Replies: 0
    • Views: 149
    01-09-2020, 02:42 PM Go to last post
  9. Suggestions for Printing Details Model

    Started by bzowk, 01-07-2020 10:28 AM
    • Replies: 3
    • Views: 260
    01-08-2020, 03:45 PM Go to last post
  10. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:22 PM
    • Replies: 1
    • Views: 223
    01-08-2020, 12:43 PM Go to last post
  11. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:05 PM
    • Replies: 0
    • Views: 145
    01-07-2020, 10:05 PM Go to last post
    • Replies: 2
    • Views: 349
    01-07-2020, 02:52 PM Go to last post
    • Replies: 0
    • Views: 137
    01-06-2020, 07:19 AM Go to last post
  12. Curving and overhand roughness

    Started by pruoccojr, 01-05-2020 09:37 PM
    • Replies: 0
    • Views: 149
    01-05-2020, 09:37 PM Go to last post
    • Replies: 2
    • Views: 327
    01-05-2020, 09:05 AM Go to last post
  13. Vertex Nano, prints too large and too small

    Started by darkG, 01-03-2020 04:05 AM
    • Replies: 2
    • Views: 316
    01-03-2020, 06:53 AM Go to last post
  14. Getting offsets when printing the outer walls

    Started by GabeG, 12-31-2019 02:28 PM
    • Replies: 2
    • Views: 339
    01-02-2020, 01:11 PM Go to last post

Page 1 of 81 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data