Close



Page 1 of 78 1231151 ... LastLast
Threads 1 to 20 of 1550

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 08:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 20,830
    10-08-2018, 04:28 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 05:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 77,148
    08-12-2016, 12:26 PM Go to last post
    • Replies: 0
    • Views: 1,404
    10-31-2015, 12:56 PM Go to last post
    • Replies: 0
    • Views: 1,786
    06-07-2015, 08:11 AM Go to last post
  1. "shark gills" printing ugh! creality cr-10s

    Started by grue, 02-07-2018 07:00 PM
    • Replies: 7
    • Views: 1,934
    02-08-2018, 05:34 PM Go to last post
  2. "Threaded" prints (picture inside)

    Started by Decoy, 11-06-2019 03:26 PM
    • Replies: 2
    • Views: 121
    11-07-2019, 03:24 PM Go to last post
  3. Exclamation "Wait for User" - Creality CR-10 S5 Error

    Started by Kairiwolfart, 04-18-2019 05:50 PM
    3dprinter, creality, error, firmware
    • Replies: 0
    • Views: 485
    04-18-2019, 05:50 PM Go to last post
  4. (Trick) Reusing limonene

    Started by hamster, 03-26-2015 11:28 AM
    • Replies: 0
    • Views: 1,607
    03-26-2015, 11:28 AM Go to last post
  5. .8 mm too big!

    Started by Perry, 07-13-2014 12:57 AM
    • Replies: 1
    • Views: 1,385
    07-13-2014, 06:20 AM Go to last post
  6. .8 nozzle troubleshooting

    Started by Alegence, 02-28-2017 07:32 PM
    • Replies: 1
    • Views: 1,546
    02-28-2017, 07:36 PM Go to last post
  7. 1st and even 2nd layer not sticking

    Started by jeromego, 01-14-2019 06:11 AM
    • Replies: 0
    • Views: 386
    01-14-2019, 06:11 AM Go to last post
  8. 1st Layer

    Started by Gramps50, 04-19-2018 12:23 PM
    • Replies: 6
    • Views: 1,578
    04-21-2018, 09:32 PM Go to last post
    • Replies: 6
    • Views: 2,190
    08-15-2016, 10:20 PM Go to last post
  9. 1st layer wavy

    Started by Huxta, 06-17-2019 11:17 AM
    • Replies: 3
    • Views: 799
    07-23-2019, 07:23 PM Go to last post
  10. 2 40mm fans at once with one printrboard?

    Started by JamesTuthill, 05-14-2014 09:43 AM
    • Replies: 2
    • Views: 2,149
    05-14-2014, 12:27 PM Go to last post
  11. 2 Used Anycubic I3 mega printers in need of help.

    Started by MegasXLR, 07-06-2019 10:59 AM
    anycubic i3, help i'm new, not working
    • Replies: 1
    • Views: 550
    07-30-2019, 06:17 AM Go to last post
  12. 20mm test problem

    Started by gblass1, 06-11-2018 10:41 PM
    • Replies: 2
    • Views: 1,521
    06-14-2018, 11:13 AM Go to last post
  13. Question 20x20x10mm Calibration Question - Z18

    Started by WireframeFX, 05-12-2016 08:23 AM
    calibration, cube, makerbot desktop, makerbot replicator z18, z18
    • Replies: 4
    • Views: 2,337
    06-06-2016, 10:03 AM Go to last post
  14. 2d gcode?

    Started by Marm, 11-24-2015 09:48 AM
    • Replies: 3
    • Views: 978
    11-24-2015, 11:25 AM Go to last post
  15. Lightbulb 3 D printer problems i have had and sorted

    Started by 01012k7, 05-08-2016 04:07 AM
    • Replies: 0
    • Views: 1,232
    05-08-2016, 04:07 AM Go to last post
  16. 3D figure articulated joints

    Started by paulsroom, 09-29-2015 08:56 PM
    kitbash niq
    • Replies: 2
    • Views: 1,499
    09-30-2015, 04:02 AM Go to last post
  17. 3D print accuracy

    Started by rossj456, 02-04-2015 03:39 PM
    • Replies: 0
    • Views: 1,116
    02-04-2015, 03:39 PM Go to last post

Page 1 of 78 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data