Close



Page 1 of 81 1231151 ... LastLast
Threads 1 to 20 of 1607

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 08:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 32
    • Views: 23,748
    01-20-2020, 11:03 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 05:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 81,047
    08-12-2016, 12:26 PM Go to last post
  1. BLTouch help please

    Started by sundown57, 01-20-2020 11:20 AM
    • Replies: 0
    • Views: 104
    01-20-2020, 11:20 AM Go to last post
  2. Any ideas

    Started by 9mmAuto, 01-19-2020 02:16 PM
    • Replies: 3
    • Views: 116
    01-20-2020, 10:02 AM Go to last post
  3. power problem

    Started by andy4751, 01-20-2020 09:35 AM
    • Replies: 0
    • Views: 48
    01-20-2020, 09:35 AM Go to last post
  4. Filament jamming - Anycubic I3 Mega

    Started by tiffachu, 01-18-2020 05:25 PM
    anycubic i3, filament jamming, help needed
    • Replies: 0
    • Views: 99
    01-18-2020, 05:25 PM Go to last post
    • Replies: 2
    • Views: 260
    01-16-2020, 02:54 PM Go to last post
  5. Angry Bad first layer need help.

    Started by gab, 01-16-2020 12:55 PM
    tevo tarantula pro
    • Replies: 0
    • Views: 118
    01-16-2020, 12:55 PM Go to last post
  6. Stop printing (Ender 3)

    Started by LupaShiva, 12-22-2019 05:10 AM
    • Replies: 3
    • Views: 434
    01-16-2020, 01:26 AM Go to last post
  7. [Problem] Ender 3 curling and not sticking to bed

    Started by notroy, 01-16-2020 12:00 AM
    • Replies: 0
    • Views: 117
    01-16-2020, 12:00 AM Go to last post
    • Replies: 8
    • Views: 547
    01-15-2020, 05:40 PM Go to last post
  8. Only one filament works

    Started by Marchello, 12-25-2019 10:09 PM
    • Replies: 3
    • Views: 290
    01-15-2020, 04:40 PM Go to last post
  9. Question Extrusion Calibration

    Started by Seb, 01-13-2020 02:27 AM
    • Replies: 0
    • Views: 14
    01-13-2020, 02:27 AM Go to last post
    • Replies: 2
    • Views: 208
    01-12-2020, 08:26 AM Go to last post
  10. Few beginner questions..

    Started by Shieldbreaker, 01-08-2020 10:07 AM
    • Replies: 2
    • Views: 264
    01-10-2020, 08:46 AM Go to last post
  11. Makerbot Replicator 2x z-axis calibration

    Started by theycallmevirgo, 01-09-2020 07:32 PM
    • Replies: 0
    • Views: 184
    01-09-2020, 07:32 PM Go to last post
  12. Issue With Prints

    Started by woodk405, 01-09-2020 04:04 PM
    • Replies: 0
    • Views: 233
    01-09-2020, 04:04 PM Go to last post
  13. CTC DOY Printer setup help - adjusting Z-position

    Started by Peterm7, 01-09-2020 02:42 PM
    ctc3d
    • Replies: 0
    • Views: 170
    01-09-2020, 02:42 PM Go to last post
  14. Suggestions for Printing Details Model

    Started by bzowk, 01-07-2020 10:28 AM
    • Replies: 3
    • Views: 288
    01-08-2020, 03:45 PM Go to last post
  15. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:22 PM
    • Replies: 1
    • Views: 259
    01-08-2020, 12:43 PM Go to last post
  16. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:05 PM
    • Replies: 0
    • Views: 176
    01-07-2020, 10:05 PM Go to last post

Page 1 of 81 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data