Close



Page 1 of 110 1231151101 ... LastLast
Threads 1 to 20 of 2193

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 08:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 63,950
    12-07-2021, 05:24 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 05:15 PM
    8 Pages
    1 2 3 ... 8
    • Replies: 72
    • Views: 140,439
    06-26-2021, 06:25 AM Go to last post
  1. Help needed for a 3D printing issue

    Started by JN84, Today 06:44 AM
    • Replies: 0
    • Views: 42
    Today, 06:44 AM Go to last post
  2. Creality CR-6 SE messy bottom help

    Started by Rhondda, Yesterday 09:20 PM
    • Replies: 0
    • Views: 93
    Yesterday, 09:20 PM Go to last post
  3. Help T'shooting Cause of Warped Print

    Started by lothian, 01-20-2022 09:52 AM
    • Replies: 2
    • Views: 425
    01-21-2022, 03:51 PM Go to last post
  4. Vertical section on all prints messes up

    Started by mbbender, 01-21-2022 01:01 PM
    • Replies: 0
    • Views: 115
    01-21-2022, 01:01 PM Go to last post
  5. yesterday

    Started by dolcevita27, 01-16-2022 08:37 AM
    • Replies: 0
    • Views: 321
    01-16-2022, 08:37 AM Go to last post
  6. PETG filament printing issues

    Started by jay3d, 01-14-2022 01:49 PM
    • Replies: 3
    • Views: 404
    01-16-2022, 05:51 AM Go to last post
  7. First layer issues

    Started by Nanookofthenorth, 01-08-2022 07:22 PM
    • Replies: 5
    • Views: 682
    01-09-2022, 09:36 AM Go to last post
  8. Out of sync dual extruder

    Started by Rockel83, 01-04-2022 07:18 PM
    • Replies: 1
    • Views: 420
    01-07-2022, 09:10 AM Go to last post
  9. CR-10 Issues

    Started by raineiac, 01-06-2022 11:03 PM
    cr-10, help post, pla++
    • Replies: 0
    • Views: 289
    01-06-2022, 11:03 PM Go to last post
  10. Best Email Marketing Software for 2022!

    Started by Emmamart, 01-05-2022 05:23 AM
    crm for sales management
    • Replies: 0
    • Views: 357
    01-05-2022, 05:23 AM Go to last post
    • Replies: 0
    • Views: 382
    01-03-2022, 12:43 AM Go to last post
  11. Ender 3 pro layer gaps and fragile prints

    Started by TLPrints25, 01-02-2022 12:31 PM
    ender3-pro
    • Replies: 0
    • Views: 418
    01-02-2022, 12:31 PM Go to last post
  12. Unhappy Hollow print. Help.

    Started by Airkout, 01-01-2022 08:54 AM
    • Replies: 9
    • Views: 907
    01-02-2022, 07:53 AM Go to last post
  13. Calibrating E-steps

    Started by Rockel83, 01-01-2022 11:55 AM
    bowden, calibration, e-steps, esteps, extruder
    • Replies: 4
    • Views: 614
    01-02-2022, 07:52 AM Go to last post
  14. Ender 3V2 gcode issues

    Started by ColmHeff, 12-31-2021 02:49 PM
    • Replies: 0
    • Views: 452
    12-31-2021, 02:49 PM Go to last post
  15. Ender3 Pro prints won't adhere to glass plate

    Started by kbcb, 11-28-2021 03:35 PM
    • Replies: 1
    • Views: 717
    12-31-2021, 12:12 AM Go to last post
  16. hot end temp reading all over the place

    Started by linky, 12-28-2021 11:14 PM
    • Replies: 0
    • Views: 448
    12-28-2021, 11:14 PM Go to last post
  17. Lightbulb Need help with big terrain print

    Started by FiftySeven, 04-27-2021 06:42 AM
    2 Pages
    1 2
    • Replies: 18
    • Views: 6,056
    12-25-2021, 09:05 AM Go to last post
  18. Prints wont stick to heatbed

    Started by DeathsmileZ, 12-15-2021 01:40 AM
    • Replies: 4
    • Views: 1,158
    12-23-2021, 03:41 AM Go to last post
    • Replies: 2
    • Views: 763
    12-23-2021, 03:24 AM Go to last post

Page 1 of 110 1231151101 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data