Close



Page 1 of 81 1231151 ... LastLast
Threads 1 to 20 of 1601

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 08:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 23,475
    10-08-2018, 04:28 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 05:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 80,774
    08-12-2016, 12:26 PM Go to last post
    • Replies: 2
    • Views: 167
    Yesterday, 02:54 PM Go to last post
  1. Angry Bad first layer need help.

    Started by gab, Yesterday 12:55 PM
    tevo tarantula pro
    • Replies: 0
    • Views: 52
    Yesterday, 12:55 PM Go to last post
  2. Stop printing (Ender 3)

    Started by LupaShiva, 12-22-2019 05:10 AM
    • Replies: 3
    • Views: 396
    Yesterday, 01:26 AM Go to last post
  3. [Problem] Ender 3 curling and not sticking to bed

    Started by notroy, Yesterday 12:00 AM
    • Replies: 0
    • Views: 80
    Yesterday, 12:00 AM Go to last post
    • Replies: 8
    • Views: 474
    01-15-2020, 05:40 PM Go to last post
  4. Only one filament works

    Started by Marchello, 12-25-2019 10:09 PM
    • Replies: 3
    • Views: 258
    01-15-2020, 04:40 PM Go to last post
    • Replies: 2
    • Views: 175
    01-12-2020, 08:26 AM Go to last post
  5. Few beginner questions..

    Started by Shieldbreaker, 01-08-2020 10:07 AM
    • Replies: 2
    • Views: 234
    01-10-2020, 08:46 AM Go to last post
  6. Makerbot Replicator 2x z-axis calibration

    Started by theycallmevirgo, 01-09-2020 07:32 PM
    • Replies: 0
    • Views: 154
    01-09-2020, 07:32 PM Go to last post
  7. Issue With Prints

    Started by woodk405, 01-09-2020 04:04 PM
    • Replies: 0
    • Views: 193
    01-09-2020, 04:04 PM Go to last post
  8. CTC DOY Printer setup help - adjusting Z-position

    Started by Peterm7, 01-09-2020 02:42 PM
    ctc3d
    • Replies: 0
    • Views: 145
    01-09-2020, 02:42 PM Go to last post
  9. Suggestions for Printing Details Model

    Started by bzowk, 01-07-2020 10:28 AM
    • Replies: 3
    • Views: 254
    01-08-2020, 03:45 PM Go to last post
  10. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:22 PM
    • Replies: 1
    • Views: 216
    01-08-2020, 12:43 PM Go to last post
  11. parts are printing at angle, help!!!!

    Started by htes, 01-07-2020 10:05 PM
    • Replies: 0
    • Views: 139
    01-07-2020, 10:05 PM Go to last post
    • Replies: 2
    • Views: 343
    01-07-2020, 02:52 PM Go to last post
    • Replies: 0
    • Views: 133
    01-06-2020, 07:19 AM Go to last post
  12. Curving and overhand roughness

    Started by pruoccojr, 01-05-2020 09:37 PM
    • Replies: 0
    • Views: 145
    01-05-2020, 09:37 PM Go to last post
    • Replies: 2
    • Views: 323
    01-05-2020, 09:05 AM Go to last post
  13. Vertex Nano, prints too large and too small

    Started by darkG, 01-03-2020 04:05 AM
    • Replies: 2
    • Views: 310
    01-03-2020, 06:53 AM Go to last post
  14. Getting offsets when printing the outer walls

    Started by GabeG, 12-31-2019 02:28 PM
    • Replies: 2
    • Views: 336
    01-02-2020, 01:11 PM Go to last post

Page 1 of 81 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data