Close
Flash Forge Guider



Page 1 of 72 1231151 ... LastLast
Threads 1 to 20 of 1438

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Red face Sticky Thread Sticky: My bloat-free STL viewer

    Started by Krishty, 11-25-2017 07:48 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 14,824
    10-08-2018, 03:28 AM Go to last post
  2. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 69,251
    08-12-2016, 11:26 AM Go to last post
  1. Creality Ender 3 Issues

    Started by DocMat, 04-23-2019 12:49 AM
    • Replies: 2
    • Views: 182
    Yesterday, 11:50 AM Go to last post
  2. heating issue

    Started by cripto101, 04-09-2019 10:23 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 1,034
    Yesterday, 12:38 AM Go to last post
  3. Bridging issue

    Started by cripto101, 04-23-2019 11:17 PM
    • Replies: 0
    • Views: 79
    04-23-2019, 11:17 PM Go to last post
  4. Question Creality Ender 3, prints suddenly total mess

    Started by DonMathi, 04-21-2019 07:18 AM
    • Replies: 2
    • Views: 259
    04-22-2019, 02:59 AM Go to last post
  5. Help with thin walls at the end of layer.

    Started by Sneaky, 04-19-2019 07:51 AM
    • Replies: 0
    • Views: 260
    04-19-2019, 07:51 AM Go to last post
    • Replies: 0
    • Views: 110
    04-19-2019, 06:21 AM Go to last post
  6. Exclamation "Wait for User" - Creality CR-10 S5 Error

    Started by Kairiwolfart, 04-18-2019 04:50 PM
    3dprinter, creality, error, firmware
    • Replies: 0
    • Views: 53
    04-18-2019, 04:50 PM Go to last post
  7. Hatchbox ABS (white) balling on second layer

    Started by jcook423, 04-17-2019 04:45 AM
    • Replies: 2
    • Views: 258
    04-18-2019, 03:54 AM Go to last post
  8. Help With Flsun i3 printer

    Started by william.deacon, 04-16-2019 11:48 PM
    flsun, help?, marlin, repetier, shifting
    • Replies: 0
    • Views: 28
    04-16-2019, 11:48 PM Go to last post
  9. Ender 3 Benchy test with PET-G

    Started by redbeardprint, 04-11-2019 08:10 PM
    • Replies: 6
    • Views: 824
    04-14-2019, 05:40 PM Go to last post
    • Replies: 2
    • Views: 204
    04-11-2019, 07:59 AM Go to last post
    • Replies: 1
    • Views: 305
    04-11-2019, 05:34 AM Go to last post
  10. Blobs/Zits on the side of printed part.

    Started by :Michael Lowell, 04-10-2019 03:22 PM
    3d print, blobs, flash forge finder, print issues, zits
    • Replies: 2
    • Views: 243
    04-10-2019, 07:14 PM Go to last post
  11. Exclamation Help needed with flashforge guider 2

    Started by dharmik, 04-09-2019 12:17 AM
    extruder issue, flashforge, flashforge 3d printer, guider2
    • Replies: 0
    • Views: 287
    04-09-2019, 12:17 AM Go to last post
  12. help!! printing stop - extruder makes a noise

    Started by machumara, 03-28-2019 08:45 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 915
    04-07-2019, 03:49 PM Go to last post
  13. Electrical Help Needed

    Started by quarinteen, 04-07-2019 01:04 PM
    • Replies: 0
    • Views: 260
    04-07-2019, 01:04 PM Go to last post
  14. Question Help with printer settings

    Started by Samarkand, 04-05-2019 02:25 PM
    • Replies: 1
    • Views: 273
    04-05-2019, 08:56 PM Go to last post
    • Replies: 3
    • Views: 319
    04-05-2019, 06:42 AM Go to last post
  15. Question Messy print on layer above support

    Started by Sorino, 04-03-2019 07:48 AM
    • Replies: 3
    • Views: 285
    04-04-2019, 10:47 AM Go to last post
  16. For first 3d printer

    Started by Danielgreen, 04-02-2019 11:27 AM
    • Replies: 2
    • Views: 271
    04-02-2019, 03:20 PM Go to last post

Page 1 of 72 1231151 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •