Close



Page 1 of 102 1231151101 ... LastLast
Threads 1 to 20 of 2036

Forum: 3D Printers (Hardware)

Discuss the various 3D Printers on the Market. Please make sure there isn't already a folder for the printer you wish to discuss in our Specific 3D Printer Folders.

  1. Sticky Thread Sticky: 3DPrint's 3D Printer Buyer's Guide

    Started by Brian_Krassenstein, 04-07-2015 12:01 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 108,625
    04-18-2021, 02:52 AM Go to last post
  1. My First CoreXY

    Started by AutoWiz, 10-03-2020 11:19 PM
    16 Pages
    1 2 3 ... 16
    • Replies: 153
    • Views: 44,878
    Today, 09:19 PM Go to last post
  2. Help with updating firmware?

    Started by CarsonGrey, 09-09-2020 02:39 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 4,874
    Yesterday, 07:09 AM Go to last post
  3. I own a Febtop Optimus - anyone else here?

    Started by coolcat, 04-14-2020 11:19 PM
    • Replies: 3
    • Views: 1,621
    05-22-2022, 06:26 AM Go to last post
    • Replies: 18
    • Views: 5,848
    05-18-2022, 06:08 AM Go to last post
  4. Exclamation BLTouch issues on SKR board

    Started by scaramonga, 07-19-2021 09:38 AM
    • Replies: 3
    • Views: 1,211
    05-17-2022, 03:44 PM Go to last post
    • Replies: 0
    • Views: 153
    05-17-2022, 03:32 PM Go to last post
  5. Fysetc Big Dipper- Getting Ready to Install

    Started by 3dpp, 05-17-2022 12:29 PM
    • Replies: 0
    • Views: 143
    05-17-2022, 12:29 PM Go to last post
  6. What would be your TOP 5 3D printers ?

    Started by Alarev, 04-11-2022 03:50 PM
    3d printer, top
    • Replies: 2
    • Views: 1,220
    05-16-2022, 10:01 AM Go to last post
  7. Question Looking for 3D Printer which meets certain Criteria

    Started by JP2K, 05-05-2022 05:17 AM
    printer
    • Replies: 2
    • Views: 715
    05-05-2022, 10:28 AM Go to last post
  8. 370mm X 250mm X 300mm

    Started by AutoWiz, 03-05-2017 10:45 PM
    35 Pages
    1 2 3 ... 35
    • Replies: 344
    • Views: 166,010
    05-05-2022, 09:10 AM Go to last post
  9. Dual Z Auto Align Setup In Marlin

    Started by AutoWiz, 09-27-2021 02:22 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 5,630
    04-30-2022, 02:07 AM Go to last post
  10. What do you do with your old printer gear?

    Started by tejas107, 12-12-2020 02:22 AM
    • Replies: 4
    • Views: 2,649
    04-27-2022, 09:53 AM Go to last post
  11. Question Extruder not working Arduino Mega 2560 Ramps 1.4

    Started by rknzkn, 04-23-2022 07:15 AM
    arduino mega, prusa steel, ramps 1.4
    • Replies: 2
    • Views: 1,068
    04-23-2022, 04:59 PM Go to last post
  12. Question Bed heat fails

    Started by Atomsk, 04-23-2022 04:54 PM
    bed heat, fail, sovol
    • Replies: 0
    • Views: 629
    04-23-2022, 04:54 PM Go to last post
  13. Which LCD printer should I get?

    Started by mountainlover, 01-30-2022 09:11 AM
    buying, resin
    • Replies: 4
    • Views: 3,069
    04-21-2022, 10:59 PM Go to last post
  14. TMC 2209 stepper drivers question

    Started by Bruce19, 03-24-2021 12:37 PM
    • Replies: 6
    • Views: 2,769
    04-18-2022, 04:00 AM Go to last post
  15. Choosing 1st printer

    Started by AlexKots, 01-26-2022 04:42 PM
    cr-10 v2, creality, micro swiss
    • Replies: 4
    • Views: 3,143
    04-05-2022, 10:45 AM Go to last post
  16. BTT Octopus Pro PT100

    Started by Petzon_Nilzon, 03-02-2022 07:43 AM
    • Replies: 4
    • Views: 1,978
    03-25-2022, 01:58 AM Go to last post
  17. Smile Budget 3D Printer Comparison Table

    Started by JuxtaMatrix, 03-23-2022 02:08 PM
    • Replies: 0
    • Views: 901
    03-23-2022, 02:08 PM Go to last post
  18. Network Printers

    Started by AutoWiz, 02-03-2017 11:25 AM
    11 Pages
    1 2 3 ... 11
    • Replies: 101
    • Views: 58,006
    03-21-2022, 05:58 AM Go to last post

Page 1 of 102 1231151101 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data