Close



Page 1 of 103 1231151101 ... LastLast
Threads 1 to 20 of 2041

Forum: 3D Printers (Hardware)

Discuss the various 3D Printers on the Market. Please make sure there isn't already a folder for the printer you wish to discuss in our Specific 3D Printer Folders.

  1. Sticky Thread Sticky: 3DPrint's 3D Printer Buyer's Guide

    Started by Brian_Krassenstein, 04-07-2015 12:01 PM
    3 Pages
    1 2 3
    • Replies: 29
    • Views: 110,733
    11-08-2020, 07:41 AM Go to last post
  1. My First CoreXY

    Started by AutoWiz, 10-03-2020 11:19 PM
    17 Pages
    1 2 3 ... 17
    • Replies: 164
    • Views: 49,787
    Yesterday, 08:15 PM Go to last post
  2. Advice on selling a Stratasys printer - Austin, TX

    Started by dnmeeks, 06-24-2022 09:44 AM
    stratasys uprint se
    • Replies: 2
    • Views: 282
    06-24-2022, 10:57 AM Go to last post
  3. Fysetc Big Dipper- Getting Ready to Install

    Started by 3dpp, 05-17-2022 12:29 PM
    • Replies: 4
    • Views: 868
    06-11-2022, 06:06 PM Go to last post
  4. What would be your TOP 5 3D printers ?

    Started by Alarev, 04-11-2022 03:50 PM
    3d printer, top
    • Replies: 4
    • Views: 1,894
    06-09-2022, 09:37 PM Go to last post
  5. Another good company going belly up

    Started by airscapes, 06-09-2022 02:31 PM
    • Replies: 0
    • Views: 402
    06-09-2022, 02:31 PM Go to last post
    • Replies: 7
    • Views: 656
    06-09-2022, 04:59 AM Go to last post
  6. What do you think about this printer ?

    Started by sdman985, 06-05-2022 02:40 PM
    • Replies: 0
    • Views: 400
    06-05-2022, 02:40 PM Go to last post
  7. Angry Ender 3 Blue Screen

    Started by 3d-Torked-Over, 06-02-2022 09:10 PM
    #bluescreen #ender3
    • Replies: 1
    • Views: 534
    06-03-2022, 10:45 AM Go to last post
  8. Pegasus 8" 3D Printer

    Started by Brian_Krassenstein, 08-14-2015 09:55 AM
    • Replies: 6
    • Views: 11,044
    06-01-2022, 10:05 PM Go to last post
  9. Printer Recommendations For Functional Prototyping?

    Started by ThePie, 05-30-2022 11:03 PM
    • Replies: 6
    • Views: 826
    06-01-2022, 08:38 PM Go to last post
  10. I own a Febtop Optimus - anyone else here?

    Started by coolcat, 04-14-2020 11:19 PM
    • Replies: 3
    • Views: 2,005
    05-22-2022, 06:26 AM Go to last post
    • Replies: 0
    • Views: 515
    05-17-2022, 03:32 PM Go to last post
  11. Question Looking for 3D Printer which meets certain Criteria

    Started by JP2K, 05-05-2022 05:17 AM
    printer
    • Replies: 2
    • Views: 1,113
    05-05-2022, 10:28 AM Go to last post
  12. What do you do with your old printer gear?

    Started by tejas107, 12-12-2020 02:22 AM
    • Replies: 4
    • Views: 2,959
    04-27-2022, 09:53 AM Go to last post
  13. Question Extruder not working Arduino Mega 2560 Ramps 1.4

    Started by rknzkn, 04-23-2022 07:15 AM
    arduino mega, prusa steel, ramps 1.4
    • Replies: 2
    • Views: 1,288
    04-23-2022, 04:59 PM Go to last post
  14. Question Bed heat fails

    Started by Atomsk, 04-23-2022 04:54 PM
    bed heat, fail, sovol
    • Replies: 0
    • Views: 787
    04-23-2022, 04:54 PM Go to last post
  15. Which LCD printer should I get?

    Started by mountainlover, 01-30-2022 09:11 AM
    buying, resin
    • Replies: 4
    • Views: 3,330
    04-21-2022, 10:59 PM Go to last post
  16. Dual Z Auto Align Setup In Marlin

    Started by AutoWiz, 09-27-2021 02:22 PM
    • Replies: 9
    • Views: 6,632
    04-16-2022, 03:37 AM Go to last post
  17. 370mm X 250mm X 300mm

    Started by AutoWiz, 03-05-2017 10:45 PM
    35 Pages
    1 2 3 ... 35
    • Replies: 343
    • Views: 171,961
    04-10-2022, 07:18 PM Go to last post
  18. Smile Budget 3D Printer Comparison Table

    Started by JuxtaMatrix, 03-23-2022 02:08 PM
    • Replies: 0
    • Views: 987
    03-23-2022, 02:08 PM Go to last post

Page 1 of 103 1231151101 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data