Close



Page 5 of 54 FirstFirst ... 3456715 ... LastLast
Threads 81 to 100 of 1064

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 01:33 AM
    33 Pages
    1 2 3 ... 33
    • Replies: 321
    • Views: 750,403
    03-12-2023, 11:59 AM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 09:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 106
    • Views: 305,691
    01-23-2023, 04:34 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 05:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 125,890
    11-07-2019, 12:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    • Replies: 6
    • Views: 47,936
    10-14-2016, 08:13 PM Go to last post
  1. Question Flashforge Creator Pro misalignment

    Started by matteog, 12-23-2020 07:45 AM
    • Replies: 0
    • Views: 3,396
    12-23-2020, 07:45 AM Go to last post
  2. Creator Pro Fuse?

    Started by jday7757, 12-17-2020 08:02 AM
    • Replies: 0
    • Views: 3,217
    12-17-2020, 08:02 AM Go to last post
  3. [GUIDER II] Filament sensor hack?

    Started by DaveH, 12-04-2020 05:38 AM
    • Replies: 6
    • Views: 6,719
    12-06-2020, 06:55 AM Go to last post
    • Replies: 1
    • Views: 3,195
    12-05-2020, 09:01 AM Go to last post
  4. Flashforge finder problem

    Started by Bad Dog, 08-16-2020 01:14 PM
    • Replies: 1
    • Views: 4,248
    12-04-2020, 06:07 AM Go to last post
  5. Angry Defect when printing with ABS

    Started by gxryy, 11-04-2020 02:54 AM
    • Replies: 2
    • Views: 4,456
    12-04-2020, 03:58 AM Go to last post
  6. Flashforge Creator Pro - Layer Problem

    Started by IanT, 11-20-2020 06:08 AM
    • Replies: 6
    • Views: 6,540
    12-03-2020, 06:45 AM Go to last post
  7. Advice required

    Started by imalc, 12-02-2020 05:46 AM
    • Replies: 2
    • Views: 3,973
    12-02-2020, 10:36 AM Go to last post
  8. Flashforge guider II s: poor layer adhesion

    Started by pelgrim, 10-17-2020 11:10 AM
    • Replies: 1
    • Views: 5,008
    11-25-2020, 05:07 AM Go to last post
    • Replies: 3
    • Views: 3,905
    11-17-2020, 08:25 AM Go to last post
  9. Older Creater Pro but wont feed in new filiment

    Started by RURC, 10-08-2020 03:25 PM
    • Replies: 5
    • Views: 4,553
    10-16-2020, 10:05 AM Go to last post
  10. Flashforge Inventor 2 levelling DIstance To Big

    Started by prayner, 08-27-2020 07:12 PM
    • Replies: 0
    • Views: 3,140
    08-27-2020, 07:12 PM Go to last post
  11. Wiring for filament detector

    Started by Stevolution2019, 08-17-2020 03:15 PM
    • Replies: 1
    • Views: 3,544
    08-19-2020, 11:33 AM Go to last post
  12. Issue with Creator Max

    Started by tonythedrony, 08-04-2020 12:34 PM
    • Replies: 2
    • Views: 3,591
    08-15-2020, 02:49 AM Go to last post
  13. Extruder Clicking - FF Creator Pro

    Started by mobrien1968, 07-21-2020 09:46 PM
    extruder clicking, flashforge creator pro, new stepper motor
    • Replies: 2
    • Views: 4,179
    08-05-2020, 07:41 PM Go to last post
  14. FFCP Motherboard Replacement

    Started by LazyWolfe, 07-16-2020 12:47 PM
    creator pro, motherboard, stepper motors
    • Replies: 0
    • Views: 2,742
    07-16-2020, 12:47 PM Go to last post
  15. Work bed sheet?

    Started by nfol, 05-23-2020 05:14 AM
    • Replies: 1
    • Views: 3,978
    07-16-2020, 12:36 PM Go to last post
    • Replies: 0
    • Views: 3,090
    07-01-2020, 07:45 AM Go to last post
  16. Filament not sticking to bed (newbie)

    Started by piecewise, 03-16-2020 03:12 PM
    • Replies: 5
    • Views: 5,189
    06-30-2020, 01:55 PM Go to last post

Page 5 of 54 FirstFirst ... 3456715 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data