Close



Page 3 of 54 FirstFirst 123451353 ... LastLast
Threads 41 to 60 of 1064

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 01:33 AM
    33 Pages
    1 2 3 ... 33
    • Replies: 321
    • Views: 750,446
    03-12-2023, 11:59 AM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 09:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 106
    • Views: 305,897
    01-23-2023, 04:34 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 05:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 125,910
    11-07-2019, 12:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    • Replies: 6
    • Views: 47,942
    10-14-2016, 08:13 PM Go to last post
  1. Newbie with problems printing the demo prints

    Started by Stephen O, 02-05-2022 02:40 PM
    finder, newbie, peeling
    • Replies: 0
    • Views: 3,346
    02-05-2022, 02:40 PM Go to last post
  2. How to not print annoying "base"?

    Started by Roy Vedas, 01-15-2022 12:42 PM
    • Replies: 7
    • Views: 6,613
    01-18-2022, 06:10 PM Go to last post
  3. Cool Flashforge Creator Pro printing setup issue

    Started by MIXEFXPRO, 12-13-2019 11:28 AM
    • Replies: 4
    • Views: 9,196
    01-17-2022, 06:02 PM Go to last post
  4. Problems printing infill

    Started by Rebmic, 01-17-2022 06:45 AM
    • Replies: 0
    • Views: 3,133
    01-17-2022, 06:45 AM Go to last post
  5. Newbie qyestion: FF Dreamer Extruder Selection

    Started by DeepSub, 01-03-2022 04:13 AM
    • Replies: 1
    • Views: 3,352
    01-03-2022, 09:32 AM Go to last post
    • Replies: 1
    • Views: 3,442
    01-02-2022, 01:13 PM Go to last post
  6. Copy Basic Configurations to expert mode?

    Started by lodcomm, 12-25-2021 02:36 PM
    • Replies: 0
    • Views: 3,193
    12-25-2021, 02:36 PM Go to last post
  7. Finder PTFE tube length

    Started by baovedenhat, 12-23-2021 12:52 PM
    • Replies: 0
    • Views: 3,035
    12-23-2021, 12:52 PM Go to last post
  8. Dreamer NX won't load filament

    Started by Finn Noodle, 12-14-2021 09:18 AM
    • Replies: 0
    • Views: 2,881
    12-14-2021, 09:18 AM Go to last post
  9. Bellen Hotmail Telefoonnummer Voor Hulp

    Started by jamasbrovn, 11-26-2021 05:29 AM
    hotmail bellen, hotmail nummer
    • Replies: 0
    • Views: 3,108
    11-26-2021, 05:29 AM Go to last post
  10. Bellen Facebook Telefoonnummer Voor Hulp

    Started by pegranjessie, 11-26-2021 05:02 AM
    facebook bellen nederland, facebook nummer
    • Replies: 0
    • Views: 2,205
    11-26-2021, 05:02 AM Go to last post
    • Replies: 0
    • Views: 2,267
    11-17-2021, 03:47 AM Go to last post
  11. I am new and getting strings

    Started by txalphadog, 11-15-2021 01:12 PM
    • Replies: 2
    • Views: 2,056
    11-15-2021, 05:07 PM Go to last post
    • Replies: 0
    • Views: 1,753
    11-07-2021, 01:08 PM Go to last post
  12. Alternative bearings for Creator Pro

    Started by baovedenhat, 10-31-2021 08:41 AM
    • Replies: 0
    • Views: 4,398
    10-31-2021, 08:41 AM Go to last post
  13. creator pro 2 - right extruder not heating up

    Started by pixelgecko, 10-19-2021 04:27 PM
    creatorpro, extruder
    • Replies: 0
    • Views: 2,587
    10-19-2021, 04:27 PM Go to last post
    • Replies: 6
    • Views: 7,897
    09-29-2021, 08:43 AM Go to last post
  14. abs woe

    Started by cwcwcw, 08-12-2021 04:05 AM
    abs, bed, temp, warp
    • Replies: 2
    • Views: 6,485
    09-25-2021, 05:25 AM Go to last post
  15. Cone makes entire circle shift 0.5mm(roughly)

    Started by cart1001, 09-24-2021 09:58 AM
    • Replies: 3
    • Views: 2,325
    09-24-2021, 11:28 AM Go to last post
  16. Quickbooks 2017 display issues

    Started by Jordy787, 07-21-2021 04:13 AM
    • Replies: 0
    • Views: 3,361
    07-21-2021, 04:13 AM Go to last post

Page 3 of 54 FirstFirst 123451353 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data