Close



Page 1 of 50 12311 ... LastLast
Threads 1 to 20 of 982

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 09:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 176,327
    12-02-2019, 05:06 AM Go to last post
  2. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 05:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 63,299
    11-07-2019, 12:23 PM Go to last post
  3. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 01:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 318
    • Views: 538,979
    01-17-2019, 04:09 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    • Replies: 6
    • Views: 22,071
    10-14-2016, 08:13 PM Go to last post
  1. Issue with Creator Max

    Started by tonythedrony, Today 12:34 PM
    • Replies: 0
    • Views: 43
    Today, 12:34 PM Go to last post
  2. Extruder Clicking - FF Creator Pro

    Started by mobrien1968, 07-21-2020 09:46 PM
    extruder clicking, flashforge creator pro, new stepper motor
    • Replies: 1
    • Views: 412
    07-28-2020, 07:12 AM Go to last post
  3. Work bed sheet?

    Started by nfol, 05-23-2020 05:14 AM
    • Replies: 2
    • Views: 698
    07-19-2020, 11:38 PM Go to last post
  4. FFCP Motherboard Replacement

    Started by LazyWolfe, 07-16-2020 12:47 PM
    creator pro, motherboard, stepper motors
    • Replies: 0
    • Views: 235
    07-16-2020, 12:47 PM Go to last post
  5. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 10:56 AM
    2 Pages
    1 2
    • Replies: 16
    • Views: 9,160
    07-08-2020, 11:16 AM Go to last post
    • Replies: 0
    • Views: 468
    07-01-2020, 07:45 AM Go to last post
  6. Filament not sticking to bed (newbie)

    Started by piecewise, 03-16-2020 03:12 PM
    • Replies: 5
    • Views: 1,768
    06-30-2020, 01:55 PM Go to last post
  7. SO frustrated with this thing

    Started by Stevolution2019, 06-08-2020 10:40 AM
    • Replies: 0
    • Views: 466
    06-08-2020, 10:40 AM Go to last post
  8. Dual Extrusion issues with Creator Pro

    Started by kevbo, 05-24-2020 04:35 PM
    all metal hotend, creator pro, dual extrusion
    • Replies: 3
    • Views: 1,173
    05-29-2020, 09:49 AM Go to last post
  9. Modifying Creator Pro firmware

    Started by joymaker2, 05-18-2020 08:20 AM
    creator pro, firmware, modify, sailfish
    • Replies: 1
    • Views: 687
    05-18-2020, 02:22 PM Go to last post
  10. Extruder heater gradually weakening

    Started by joymaker2, 05-18-2020 07:58 AM
    creator pro, heater
    • Replies: 1
    • Views: 537
    05-18-2020, 08:13 AM Go to last post
  11. Need replacement fan screws

    Started by joymaker2, 05-18-2020 07:56 AM
    creator pro, fan, screws
    • Replies: 0
    • Views: 368
    05-18-2020, 07:56 AM Go to last post
  12. FF Creator Pro - Last layer not finishing well

    Started by 3rdSpace, 05-13-2020 03:05 PM
    • Replies: 0
    • Views: 502
    05-13-2020, 03:05 PM Go to last post
  13. ABS not extruding very well.

    Started by AllTheWay, 05-08-2020 09:51 PM
    • Replies: 4
    • Views: 864
    05-09-2020, 10:33 AM Go to last post
  14. Adventurer 3 - Connect to cloud

    Started by DaveParker, 05-05-2020 05:09 AM
    adventurer3, camera, cloud, sz3dp
    • Replies: 0
    • Views: 537
    05-05-2020, 05:09 AM Go to last post
  15. z-axis consistant gap

    Started by blairmi2, 04-24-2020 02:05 PM
    • Replies: 0
    • Views: 865
    04-24-2020, 02:05 PM Go to last post
  16. Creator Dual LCD issues

    Started by pub1tzu, 04-21-2020 03:18 PM
    • Replies: 0
    • Views: 590
    04-21-2020, 03:18 PM Go to last post
    • Replies: 2
    • Views: 4,053
    03-28-2020, 06:36 AM Go to last post
    • Replies: 2
    • Views: 2,070
    03-26-2020, 05:14 PM Go to last post

Page 1 of 50 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data