Close



Page 1 of 50 12311 ... LastLast
Threads 1 to 20 of 994

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 319
    • Views: 553,189
    11-18-2020, 12:06 PM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 184,904
    12-02-2019, 06:06 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 66,974
    11-07-2019, 01:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 23,988
    10-14-2016, 09:13 PM Go to last post
    • Replies: 2
    • Views: 71
    Today, 11:20 AM Go to last post
  1. [GUIDER II] Filament sensor hack?

    Started by DaveH, Today 06:38 AM
    • Replies: 2
    • Views: 45
    Today, 09:25 AM Go to last post
  2. Flashforge finder problem

    Started by Bad Dog, 08-16-2020 02:14 PM
    • Replies: 1
    • Views: 1,113
    Today, 07:07 AM Go to last post
  3. Angry Defect when printing with ABS

    Started by gxryy, 11-04-2020 03:54 AM
    • Replies: 2
    • Views: 814
    Today, 04:58 AM Go to last post
    • Replies: 0
    • Views: 246
    Yesterday, 10:22 AM Go to last post
  4. Flashforge Creator Pro - Layer Problem

    Started by IanT, 11-20-2020 07:08 AM
    • Replies: 6
    • Views: 679
    Yesterday, 07:45 AM Go to last post
  5. Advice required

    Started by imalc, 12-02-2020 06:46 AM
    • Replies: 2
    • Views: 175
    12-02-2020, 11:36 AM Go to last post
  6. Flashforge guider II s: poor layer adhesion

    Started by pelgrim, 10-17-2020 12:10 PM
    • Replies: 1
    • Views: 1,556
    11-25-2020, 06:07 AM Go to last post
    • Replies: 3
    • Views: 828
    11-17-2020, 09:25 AM Go to last post
  7. Older Creater Pro but wont feed in new filiment

    Started by RURC, 10-08-2020 04:25 PM
    • Replies: 5
    • Views: 1,623
    10-16-2020, 11:05 AM Go to last post
  8. Electric Shock

    Started by adam1972, 05-23-2017 09:00 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 9,493
    09-13-2020, 05:48 PM Go to last post
  9. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 11:56 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 12,070
    09-07-2020, 12:58 PM Go to last post
  10. Flashforge Inventor 2 levelling DIstance To Big

    Started by prayner, 08-27-2020 08:12 PM
    • Replies: 0
    • Views: 1,081
    08-27-2020, 08:12 PM Go to last post
  11. Wiring for filament detector

    Started by Stevolution2019, 08-17-2020 04:15 PM
    • Replies: 1
    • Views: 1,345
    08-19-2020, 12:33 PM Go to last post
  12. Issue with Creator Max

    Started by tonythedrony, 08-04-2020 01:34 PM
    • Replies: 2
    • Views: 1,396
    08-15-2020, 03:49 AM Go to last post
  13. Extruder Clicking - FF Creator Pro

    Started by mobrien1968, 07-21-2020 10:46 PM
    extruder clicking, flashforge creator pro, new stepper motor
    • Replies: 2
    • Views: 1,922
    08-05-2020, 08:41 PM Go to last post
  14. Work bed sheet?

    Started by nfol, 05-23-2020 06:14 AM
    • Replies: 2
    • Views: 1,697
    07-20-2020, 12:38 AM Go to last post
  15. FFCP Motherboard Replacement

    Started by LazyWolfe, 07-16-2020 01:47 PM
    creator pro, motherboard, stepper motors
    • Replies: 0
    • Views: 1,105
    07-16-2020, 01:47 PM Go to last post
    • Replies: 0
    • Views: 1,373
    07-01-2020, 08:45 AM Go to last post
  16. Filament not sticking to bed (newbie)

    Started by piecewise, 03-16-2020 04:12 PM
    • Replies: 5
    • Views: 2,746
    06-30-2020, 02:55 PM Go to last post

Page 1 of 50 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data