Close



Page 1 of 48 12311 ... LastLast
Threads 1 to 20 of 951

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 54,619
    11-07-2019, 01:23 PM Go to last post
  2. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 318
    • Views: 511,167
    01-17-2019, 05:09 PM Go to last post
  3. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 18,693
    10-14-2016, 09:13 PM Go to last post
  4. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 102
    • Views: 157,447
    08-29-2016, 02:05 AM Go to last post
  1. Getting it to stick !!

    Started by muddledsteve, 11-05-2019 04:01 PM
    • Replies: 0
    • Views: 73
    11-05-2019, 04:01 PM Go to last post
  2. PETG dry vs ‘wet’

    Started by DaveyG, 10-23-2019 09:46 AM
    • Replies: 2
    • Views: 728
    10-23-2019, 05:34 PM Go to last post
  3. Replacement drive gear

    Started by Stevolution2019, 09-23-2019 01:03 PM
    • Replies: 6
    • Views: 1,465
    10-13-2019, 12:51 PM Go to last post
  4. Flashforge Dreamer Issue

    Started by AdrianJLock, 09-27-2019 05:52 AM
    • Replies: 2
    • Views: 809
    10-07-2019, 03:08 AM Go to last post
  5. Prints getting worse - PETG

    Started by Stevolution2019, 09-26-2019 10:11 AM
    • Replies: 1
    • Views: 459
    09-27-2019, 04:36 AM Go to last post
    • Replies: 7
    • Views: 1,096
    09-25-2019, 01:50 PM Go to last post
  6. FF Creator Pro Raspberry Pi 3 where to mount?

    Started by RegisG, 09-23-2019 10:48 PM
    • Replies: 0
    • Views: 306
    09-23-2019, 10:48 PM Go to last post
  7. Removing the blue 3M platform stickers

    Started by dommer2029, 09-30-2015 04:18 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 24,712
    09-09-2019, 01:01 PM Go to last post
  8. Question FlashForge New Creator Pro ont the way - Novice

    Started by RegisG, 08-29-2019 01:10 PM
    • Replies: 3
    • Views: 1,156
    09-06-2019, 03:51 PM Go to last post
  9. Adventurer 3 Issue

    Started by wy1c, 08-31-2019 08:06 PM
    • Replies: 1
    • Views: 695
    09-04-2019, 06:11 AM Go to last post
  10. FFCP travel off in X axis

    Started by DaveyG, 07-11-2019 12:59 PM
    • Replies: 2
    • Views: 5,219
    07-15-2019, 11:18 AM Go to last post
  11. FFCP Tool 1 Failure!

    Started by DaveyG, 07-11-2019 10:27 AM
    • Replies: 1
    • Views: 1,176
    07-11-2019, 11:18 AM Go to last post
    • Replies: 1
    • Views: 1,522
    06-14-2019, 07:51 AM Go to last post
  12. FlashPrint grossly underestimating time?

    Started by DaveyG, 05-28-2019 02:56 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 2,659
    06-10-2019, 10:31 AM Go to last post
  13. Adventurer 3 Build Surface not level

    Started by GhenghisConn, 06-06-2019 06:16 PM
    • Replies: 1
    • Views: 920
    06-07-2019, 01:33 PM Go to last post
  14. Sourcing a metal x-axis idler pulley

    Started by roykirk, 06-05-2019 10:41 AM
    • Replies: 0
    • Views: 828
    06-05-2019, 10:41 AM Go to last post
  15. flashforge finder optimum settings

    Started by GEORGIEBOY48, 05-20-2019 08:01 AM
    • Replies: 0
    • Views: 1,064
    05-20-2019, 08:01 AM Go to last post
  16. finder calibration

    Started by GEORGIEBOY48, 05-18-2019 08:23 AM
    • Replies: 0
    • Views: 898
    05-18-2019, 08:23 AM Go to last post
    • Replies: 5
    • Views: 2,154
    05-09-2019, 12:35 PM Go to last post
  17. Supports breaking off mid-print

    Started by DrinkMoxie, 05-07-2019 05:53 PM
    • Replies: 5
    • Views: 1,567
    05-08-2019, 05:33 PM Go to last post

Page 1 of 48 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data