Close



Page 1 of 49 12311 ... LastLast
Threads 1 to 20 of 976

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 09:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 171,418
    12-02-2019, 05:06 AM Go to last post
  2. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 05:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 61,273
    11-07-2019, 12:23 PM Go to last post
  3. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 01:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 318
    • Views: 531,486
    01-17-2019, 04:09 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    • Replies: 6
    • Views: 21,190
    10-14-2016, 08:13 PM Go to last post
  1. Dual Extrusion issues with Creator Pro

    Started by kevbo, 05-24-2020 04:35 PM
    all metal hotend, creator pro, dual extrusion
    • Replies: 3
    • Views: 324
    Today, 09:49 AM Go to last post
  2. Work bed sheet?

    Started by nfol, 05-23-2020 05:14 AM
    • Replies: 0
    • Views: 153
    05-23-2020, 05:14 AM Go to last post
  3. Modifying Creator Pro firmware

    Started by joymaker2, 05-18-2020 08:20 AM
    creator pro, firmware, modify, sailfish
    • Replies: 1
    • Views: 317
    05-18-2020, 02:22 PM Go to last post
  4. Extruder heater gradually weakening

    Started by joymaker2, 05-18-2020 07:58 AM
    creator pro, heater
    • Replies: 1
    • Views: 152
    05-18-2020, 08:13 AM Go to last post
  5. Need replacement fan screws

    Started by joymaker2, 05-18-2020 07:56 AM
    creator pro, fan, screws
    • Replies: 0
    • Views: 103
    05-18-2020, 07:56 AM Go to last post
  6. FF Creator Pro - Last layer not finishing well

    Started by 3rdSpace, 05-13-2020 03:05 PM
    • Replies: 0
    • Views: 225
    05-13-2020, 03:05 PM Go to last post
  7. ABS not extruding very well.

    Started by AllTheWay, 05-08-2020 09:51 PM
    • Replies: 4
    • Views: 390
    05-09-2020, 10:33 AM Go to last post
  8. Adventurer 3 - Connect to cloud

    Started by DaveParker, 05-05-2020 05:09 AM
    adventurer3, camera, cloud, sz3dp
    • Replies: 0
    • Views: 281
    05-05-2020, 05:09 AM Go to last post
  9. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 10:56 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 7,194
    05-04-2020, 09:49 AM Go to last post
  10. z-axis consistant gap

    Started by blairmi2, 04-24-2020 02:05 PM
    • Replies: 0
    • Views: 579
    04-24-2020, 02:05 PM Go to last post
  11. Creator Dual LCD issues

    Started by pub1tzu, 04-21-2020 03:18 PM
    • Replies: 0
    • Views: 328
    04-21-2020, 03:18 PM Go to last post
  12. Adventurer 3 Feeder Popping/Clicking

    Started by sinabu, 04-13-2019 05:12 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 10,550
    04-10-2020, 02:53 PM Go to last post
  13. Cleaning the kapton

    Started by Billzilla, 04-14-2014 03:21 AM
    2 Pages
    1 2
    • Replies: 18
    • Views: 8,897
    04-10-2020, 02:50 PM Go to last post
    • Replies: 2
    • Views: 3,695
    03-28-2020, 06:36 AM Go to last post
    • Replies: 2
    • Views: 1,776
    03-26-2020, 05:14 PM Go to last post
  14. Filament not sticking to bed (newbie)

    Started by piecewise, 03-16-2020 03:12 PM
    • Replies: 2
    • Views: 923
    03-19-2020, 04:05 PM Go to last post
    • Replies: 0
    • Views: 1,134
    02-26-2020, 03:49 PM Go to last post
  15. Flashforge Adventurer 3 MAC Address

    Started by psychodelicpenguin, 01-12-2019 02:58 AM
    • Replies: 4
    • Views: 3,952
    02-25-2020, 07:04 PM Go to last post
  16. Adventurer 3

    Started by MikeD, 02-21-2020 05:59 AM
    • Replies: 1
    • Views: 1,444
    02-21-2020, 02:22 PM Go to last post
    • Replies: 0
    • Views: 919
    02-18-2020, 12:25 PM Go to last post

Page 1 of 49 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data