Close



Page 1 of 51 12311 ... LastLast
Threads 1 to 20 of 1002

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    33 Pages
    1 2 3 ... 33
    • Replies: 320
    • Views: 559,399
    01-03-2021, 09:24 AM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 188,559
    12-02-2019, 06:06 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 68,497
    11-07-2019, 01:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 24,820
    10-14-2016, 09:13 PM Go to last post
  1. Adventurer 3 NinjaFlex and FlashPrint

    Started by budmaniac, 01-16-2021 03:59 PM
    adventurer 3, flashprint, ninjaflex
    • Replies: 0
    • Views: 132
    01-16-2021, 03:59 PM Go to last post
  2. Question Flashprint 4.6 issue on Linux (with nVidia)

    Started by kaipee, 01-15-2021 11:25 AM
    flashprint, linux
    • Replies: 0
    • Views: 137
    01-15-2021, 11:25 AM Go to last post
  3. Flashforge Finder Bed Problem

    Started by Raypow, 01-14-2021 06:44 AM
    • Replies: 0
    • Views: 161
    01-14-2021, 06:44 AM Go to last post
  4. Internal SD card dreamer.

    Started by bookworm1707, 01-31-2017 03:21 AM
    • Replies: 3
    • Views: 2,941
    01-13-2021, 03:15 PM Go to last post
  5. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 11:56 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 13,262
    01-13-2021, 04:22 AM Go to last post
  6. Newbie with Flashforge Issues: Help please

    Started by Streetsnake, 01-07-2021 03:25 PM
    • Replies: 1
    • Views: 355
    01-07-2021, 03:32 PM Go to last post
  7. FF Creator 3 first layer adhesion issues

    Started by davaze, 01-03-2021 07:16 AM
    • Replies: 0
    • Views: 289
    01-03-2021, 07:16 AM Go to last post
    • Replies: 0
    • Views: 480
    12-28-2020, 01:54 AM Go to last post
  8. Question Flashforge Creator Pro misalignment

    Started by matteog, 12-23-2020 08:45 AM
    • Replies: 0
    • Views: 645
    12-23-2020, 08:45 AM Go to last post
  9. Creator Pro Fuse?

    Started by jday7757, 12-17-2020 09:02 AM
    • Replies: 0
    • Views: 608
    12-17-2020, 09:02 AM Go to last post
  10. [GUIDER II] Filament sensor hack?

    Started by DaveH, 12-04-2020 06:38 AM
    • Replies: 6
    • Views: 1,614
    12-06-2020, 07:55 AM Go to last post
    • Replies: 7
    • Views: 1,564
    12-05-2020, 12:06 PM Go to last post
    • Replies: 1
    • Views: 850
    12-05-2020, 10:01 AM Go to last post
  11. Flashforge finder problem

    Started by Bad Dog, 08-16-2020 02:14 PM
    • Replies: 1
    • Views: 1,653
    12-04-2020, 07:07 AM Go to last post
  12. Angry Defect when printing with ABS

    Started by gxryy, 11-04-2020 03:54 AM
    • Replies: 2
    • Views: 1,363
    12-04-2020, 04:58 AM Go to last post
  13. Flashforge Creator Pro - Layer Problem

    Started by IanT, 11-20-2020 07:08 AM
    • Replies: 6
    • Views: 1,448
    12-03-2020, 07:45 AM Go to last post
  14. Advice required

    Started by imalc, 12-02-2020 06:46 AM
    • Replies: 2
    • Views: 784
    12-02-2020, 11:36 AM Go to last post
  15. Flashforge guider II s: poor layer adhesion

    Started by pelgrim, 10-17-2020 12:10 PM
    • Replies: 1
    • Views: 2,117
    11-25-2020, 06:07 AM Go to last post
    • Replies: 3
    • Views: 1,418
    11-17-2020, 09:25 AM Go to last post
  16. Older Creater Pro but wont feed in new filiment

    Started by RURC, 10-08-2020 04:25 PM
    • Replies: 5
    • Views: 2,199
    10-16-2020, 11:05 AM Go to last post

Page 1 of 51 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data