Close



Page 1 of 48 12311 ... LastLast
Threads 1 to 20 of 949

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 01:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 318
    • Views: 508,101
    01-17-2019, 04:09 PM Go to last post
  2. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 05:24 PM
    3 Pages
    1 2 3
    • Replies: 23
    • Views: 53,742
    10-24-2018, 06:40 AM Go to last post
  3. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    • Replies: 6
    • Views: 18,418
    10-14-2016, 08:13 PM Go to last post
  4. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 09:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 102
    • Views: 155,842
    08-29-2016, 01:05 AM Go to last post
  1. Replacement drive gear

    Started by Stevolution2019, 09-23-2019 12:03 PM
    • Replies: 6
    • Views: 773
    10-13-2019, 11:51 AM Go to last post
  2. Flashforge Dreamer Issue

    Started by AdrianJLock, 09-27-2019 04:52 AM
    • Replies: 2
    • Views: 604
    10-07-2019, 02:08 AM Go to last post
  3. Prints getting worse - PETG

    Started by Stevolution2019, 09-26-2019 09:11 AM
    • Replies: 1
    • Views: 293
    09-27-2019, 03:36 AM Go to last post
    • Replies: 8
    • Views: 909
    09-25-2019, 12:50 PM Go to last post
  4. FF Creator Pro Raspberry Pi 3 where to mount?

    Started by RegisG, 09-23-2019 09:48 PM
    • Replies: 0
    • Views: 197
    09-23-2019, 09:48 PM Go to last post
  5. Removing the blue 3M platform stickers

    Started by dommer2029, 09-30-2015 03:18 PM
    2 Pages
    1 2
    • Replies: 17
    • Views: 24,317
    09-09-2019, 12:01 PM Go to last post
  6. Question FlashForge New Creator Pro ont the way - Novice

    Started by RegisG, 08-29-2019 12:10 PM
    • Replies: 3
    • Views: 1,032
    09-06-2019, 02:51 PM Go to last post
  7. Adventurer 3 Issue

    Started by wy1c, 08-31-2019 07:06 PM
    • Replies: 1
    • Views: 572
    09-04-2019, 05:11 AM Go to last post
  8. FFCP travel off in X axis

    Started by DaveyG, 07-11-2019 11:59 AM
    • Replies: 2
    • Views: 4,617
    07-15-2019, 10:18 AM Go to last post
  9. FFCP Tool 1 Failure!

    Started by DaveyG, 07-11-2019 09:27 AM
    • Replies: 1
    • Views: 1,035
    07-11-2019, 10:18 AM Go to last post
    • Replies: 1
    • Views: 1,385
    06-14-2019, 06:51 AM Go to last post
  10. FlashPrint grossly underestimating time?

    Started by DaveyG, 05-28-2019 01:56 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 2,485
    06-10-2019, 09:31 AM Go to last post
  11. Adventurer 3 Build Surface not level

    Started by GhenghisConn, 06-06-2019 05:16 PM
    • Replies: 1
    • Views: 821
    06-07-2019, 12:33 PM Go to last post
  12. Sourcing a metal x-axis idler pulley

    Started by roykirk, 06-05-2019 09:41 AM
    • Replies: 0
    • Views: 729
    06-05-2019, 09:41 AM Go to last post
  13. flashforge finder optimum settings

    Started by GEORGIEBOY48, 05-20-2019 07:01 AM
    • Replies: 0
    • Views: 964
    05-20-2019, 07:01 AM Go to last post
  14. finder calibration

    Started by GEORGIEBOY48, 05-18-2019 07:23 AM
    • Replies: 0
    • Views: 803
    05-18-2019, 07:23 AM Go to last post
    • Replies: 5
    • Views: 1,986
    05-09-2019, 11:35 AM Go to last post
  15. Supports breaking off mid-print

    Started by DrinkMoxie, 05-07-2019 04:53 PM
    • Replies: 5
    • Views: 1,463
    05-08-2019, 04:33 PM Go to last post
    • Replies: 0
    • Views: 795
    05-05-2019, 12:30 PM Go to last post
  16. Warped Prints

    Started by ixlr8, 03-23-2014 12:57 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 9,643
    05-05-2019, 10:40 AM Go to last post

Page 1 of 48 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •