Close
Flash Forge Guider



Page 4 of 149 FirstFirst ... 234561454104 ... LastLast
Threads 61 to 80 of 2967

Forum: General 3D Printing Discussion

Anything Related to the 3D Printing Industry which doesn't belong in the our other folders goes here.

  1. Question Sticky Thread Sticky: Best 3D printer for me? Comment advice.

    Started by Ben2900, 04-26-2017 08:44 AM
    6 Pages
    1 2 3 ... 6
    3dprinter, advice, best 3d printer
    • Replies: 54
    • Views: 18,103
    05-06-2019, 09:03 AM Go to last post
  2. Sticky Thread Sticky: Technical Information Resources

    Started by Ward, 11-23-2015 09:37 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 6,141
    12-29-2018, 05:58 AM Go to last post
  3. Sticky Thread Sticky: UK TCT 2018 - This Week :-)

    Started by curious aardvark, 09-24-2018 07:54 AM
    • Replies: 4
    • Views: 1,667
    10-01-2018, 08:23 AM Go to last post
    • Replies: 5
    • Views: 662
    03-07-2019, 02:39 PM Go to last post
  1. Will this work with PLA/ABS?

    Started by helpmz, 03-06-2019 06:38 PM
    • Replies: 4
    • Views: 781
    03-07-2019, 11:29 AM Go to last post
  2. Issue with XYZ 3D printer

    Started by bobdidit, 03-03-2019 09:38 AM
    3d printer, xyz printer
    • Replies: 1
    • Views: 481
    03-07-2019, 12:49 AM Go to last post
  3. Printing Problem, need some help.

    Started by apun77, 03-05-2019 05:25 AM
    • Replies: 1
    • Views: 370
    03-05-2019, 05:34 AM Go to last post
  4. Question Cura sending wrong instructions?

    Started by IAMspeedex, 02-28-2019 02:29 PM
    • Replies: 1
    • Views: 348
    02-28-2019, 02:59 PM Go to last post
  5. ender 3 not printing

    Started by elpiko, 02-26-2019 09:46 AM
    • Replies: 1
    • Views: 454
    02-26-2019, 03:50 PM Go to last post
  6. initial success...then failure

    Started by honerboys, 02-18-2019 03:26 PM
    • Replies: 6
    • Views: 851
    02-22-2019, 11:55 AM Go to last post
  7. MP Maker Select v2 Marlin Installation gone wrong

    Started by Pankh, 02-15-2019 11:10 PM
    • Replies: 1
    • Views: 313
    02-19-2019, 01:35 PM Go to last post
  8. Issues with small borders on layers

    Started by TheBigC, 02-14-2019 12:34 PM
    • Replies: 3
    • Views: 447
    02-19-2019, 01:31 PM Go to last post
  9. HELP - First Row Not Printing Properly

    Started by Firepower, 02-02-2019 05:22 AM
    • Replies: 9
    • Views: 871
    02-16-2019, 11:18 PM Go to last post
  10. Exclamation Autohome failure + poor printing quality

    Started by Emwyo, 02-16-2019 02:27 PM
    • Replies: 0
    • Views: 231
    02-16-2019, 02:27 PM Go to last post
  11. Successful 1st ABS Print

    Started by Roberts_Clif, 09-15-2018 05:39 PM
    • Replies: 8
    • Views: 1,305
    02-16-2019, 10:48 AM Go to last post
  12. E-Bay Delta

    Started by Roberts_Clif, 02-15-2019 10:23 AM
    • Replies: 1
    • Views: 294
    02-15-2019, 02:01 PM Go to last post
  13. What 3D printer should I get?

    Started by Tиtaн, 02-03-2019 12:15 AM
    buy, noob, specifications
    • Replies: 5
    • Views: 651
    02-15-2019, 06:07 AM Go to last post
    • Replies: 0
    • Views: 277
    02-15-2019, 02:26 AM Go to last post
  14. trouble getting good prints on an ender 2

    Started by gkyle840, 02-14-2019 01:23 PM
    • Replies: 0
    • Views: 284
    02-14-2019, 01:23 PM Go to last post
  15. How much would it cost to print a figure?

    Started by TobiWan, 12-28-2018 02:42 PM
    • Replies: 6
    • Views: 1,091
    02-13-2019, 05:35 PM Go to last post
  16. Ender 3 Petg problems

    Started by rfrogner, 02-12-2019 01:34 PM
    • Replies: 1
    • Views: 361
    02-13-2019, 08:29 AM Go to last post
  17. Question Filament sensor problem cr-10s pro

    Started by Spolek, 02-12-2019 04:27 PM
    • Replies: 0
    • Views: 380
    02-12-2019, 04:27 PM Go to last post
    • Replies: 31
    • Views: 2,054
    02-09-2019, 09:51 PM Go to last post

Page 4 of 149 FirstFirst ... 234561454104 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •