Close



Page 1 of 171 1231151101 ... LastLast
Threads 1 to 20 of 3409

Forum: General 3D Printing Discussion

Anything Related to the 3D Printing Industry which doesn't belong in the our other folders goes here.

  1. Sticky Thread Sticky: TCT 2019 NEC Birmingham

    Started by curious aardvark, 09-24-2019 11:47 AM
    • Replies: 7
    • Views: 5,402
    09-01-2020, 10:10 AM Go to last post
    • Replies: 15
    • Views: 11,518
    09-01-2020, 02:59 AM Go to last post
  2. Sticky Thread Sticky: Technical Information Resources

    Started by Ward, 11-23-2015 09:37 AM
    • Replies: 6
    • Views: 18,772
    08-11-2020, 07:09 AM Go to last post
  3. Sticky Thread Sticky: Printing anti-droplet face shields.

    Started by PPEprinter, 04-01-2020 02:13 AM
    • Replies: 8
    • Views: 3,375
    07-21-2020, 04:32 AM Go to last post
  4. Question Sticky Thread Sticky: Best 3D printer for me? Comment advice.

    Started by Ben2900, 04-26-2017 08:44 AM
    9 Pages
    1 2 3 ... 9
    3dman, 3dprinter, advice, best 3d printer
    • Replies: 81
    • Views: 55,254
    07-06-2020, 05:54 AM Go to last post
  1. CanaKit Raspberry

    Started by TreeTolber, Yesterday 03:22 PM
    • Replies: 0
    • Views: 75
    Yesterday, 03:22 PM Go to last post
    • Replies: 2
    • Views: 211
    Yesterday, 08:47 AM Go to last post
  2. Earn money with printer

    Started by Leifn, 04-25-2020 04:23 PM
    • Replies: 8
    • Views: 3,755
    09-25-2020, 11:05 AM Go to last post
  3. making money from 3d printing?

    Started by cipher0, 03-20-2014 05:14 AM
    9 Pages
    1 2 3 ... 9
    • Replies: 84
    • Views: 51,907
    09-25-2020, 09:17 AM Go to last post
  4. EnvisionTec Perfactory IV

    Started by Robbo1970, 09-10-2020 06:26 AM
    • Replies: 2
    • Views: 195
    09-25-2020, 07:11 AM Go to last post
  5. News Watch Immortals on FandangoNOW

    Started by aragatses, 09-25-2020 06:02 AM
    fandangonow.com/activate
    • Replies: 0
    • Views: 65
    09-25-2020, 06:02 AM Go to last post
  6. Question Looking for large 3D printer

    Started by jeffmorris, 08-22-2020 06:30 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 2,108
    09-24-2020, 02:05 PM Go to last post
  7. General help

    Started by Lord Hood, 09-05-2020 09:31 AM
    • Replies: 6
    • Views: 439
    09-24-2020, 10:38 AM Go to last post
  8. Sprider Webs and hair?

    Started by threedee4me, 08-20-2016 08:27 PM
    • Replies: 8
    • Views: 3,188
    09-24-2020, 04:19 AM Go to last post
  9. Interview about 3D printing tech

    Started by Whw6065, 09-22-2020 09:46 AM
    • Replies: 4
    • Views: 283
    09-23-2020, 12:18 PM Go to last post
    • Replies: 3
    • Views: 179
    09-23-2020, 11:21 AM Go to last post
  10. News Discussion about this forum

    Started by RuthBrown, 09-23-2020 08:23 AM
    • Replies: 1
    • Views: 135
    09-23-2020, 11:02 AM Go to last post
  11. Exclamation Initial layer not adhering/ dragging of filament

    Started by Lewis96, 09-11-2020 11:00 AM
    • Replies: 6
    • Views: 615
    09-22-2020, 02:48 PM Go to last post
  12. Printed part does not stick on the heated bed

    Started by emilytako, 01-08-2020 07:43 PM
    • Replies: 9
    • Views: 2,075
    09-21-2020, 06:40 AM Go to last post
  13. News New IDEX direct drive 3d printer launch at kickstarte

    Started by jgmaker, 09-15-2020 07:31 AM
    3d printer
    • Replies: 2
    • Views: 287
    09-18-2020, 11:37 AM Go to last post
  14. Newbie needs help with firmware

    Started by bossnut, 09-16-2020 10:18 AM
    • Replies: 4
    • Views: 322
    09-17-2020, 10:40 AM Go to last post
    • Replies: 0
    • Views: 169
    09-17-2020, 04:06 AM Go to last post
  15. Wanna Discuss Something

    Started by RuthBrown, 09-16-2020 04:52 AM
    • Replies: 0
    • Views: 209
    09-16-2020, 04:52 AM Go to last post
  16. Wanna Discuss Something

    Started by Ray66, 09-14-2020 11:11 PM
    • Replies: 1
    • Views: 234
    09-15-2020, 03:22 PM Go to last post

Page 1 of 171 1231151101 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data