Close
Flash Forge Adventurer 3



Page 1 of 147 1231151101 ... LastLast
Threads 1 to 20 of 2923

Forum: General 3D Printing Discussion

Anything Related to the 3D Printing Industry which doesn't belong in the our other folders goes here.

  1. Question Sticky Thread Sticky: Best 3D printer for me? Comment advice.

    Started by Ben2900, 04-26-2017 08:44 AM
    5 Pages
    1 2 3 ... 5
    3dprinter, advice, best 3d printer
    • Replies: 45
    • Views: 15,819
    02-28-2019, 07:20 PM Go to last post
  2. Sticky Thread Sticky: Technical Information Resources

    Started by Ward, 11-23-2015 09:37 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 5,498
    12-29-2018, 05:58 AM Go to last post
  3. Sticky Thread Sticky: UK TCT 2018 - This Week :-)

    Started by curious aardvark, 09-24-2018 07:54 AM
    • Replies: 4
    • Views: 1,319
    10-01-2018, 08:23 AM Go to last post
  1. Purchasing a 3D printer with a service contract

    Started by pfontaine2, 03-15-2019 08:27 AM
    • Replies: 2
    • Views: 97
    Today, 10:02 AM Go to last post
  2. Smile Settings in MakerBot Print (Macintosh)

    Started by Torby, 03-14-2019 09:21 PM
    • Replies: 4
    • Views: 167
    Yesterday, 06:29 AM Go to last post
  3. First printer Layer quailty

    Started by DRFTBLD, 03-11-2019 08:38 PM
    • Replies: 3
    • Views: 191
    03-14-2019, 08:18 AM Go to last post
  4. FLSUN Printer Issue

    Started by MHPrior80, 03-05-2019 03:40 PM
    4 Pages
    1 2 3 ... 4
    • Replies: 34
    • Views: 1,252
    03-13-2019, 04:32 PM Go to last post
  5. is there an FFF printer that ACTUALLY WORKS?

    Started by kek, 03-12-2019 01:05 PM
    • Replies: 2
    • Views: 178
    03-12-2019, 01:52 PM Go to last post
  6. Layer huge gaps

    Started by stgm1, 03-12-2019 05:46 AM
    • Replies: 2
    • Views: 171
    03-12-2019, 07:56 AM Go to last post
  7. Veins in 3d print (cura 3.6.0)

    Started by fnielson1, 03-10-2019 03:57 PM
    • Replies: 0
    • Views: 145
    03-10-2019, 03:57 PM Go to last post
  8. 3d printer houses

    Started by kashimarki, 08-31-2014 03:24 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 3,213
    03-09-2019, 11:53 AM Go to last post
  9. When will we be 3D printing all houses?

    Started by Amy, 02-16-2019 05:31 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 821
    03-08-2019, 08:04 PM Go to last post
  10. help figuring out problem?

    Started by Usmcninjaman, 03-08-2019 10:07 AM
    • Replies: 3
    • Views: 349
    03-08-2019, 11:40 AM Go to last post
  11. EZT3D T1 sd card reader help

    Started by davecardella, 03-07-2019 11:17 PM
    ezt3d t1, sd card reader
    • Replies: 0
    • Views: 149
    03-07-2019, 11:17 PM Go to last post
    • Replies: 2
    • Views: 219
    03-07-2019, 03:07 PM Go to last post
    • Replies: 5
    • Views: 444
    03-07-2019, 02:39 PM Go to last post
  12. Will this work with PLA/ABS?

    Started by helpmz, 03-06-2019 06:38 PM
    • Replies: 4
    • Views: 448
    03-07-2019, 11:29 AM Go to last post
  13. Issue with XYZ 3D printer

    Started by bobdidit, 03-03-2019 09:38 AM
    3d printer, xyz printer
    • Replies: 1
    • Views: 295
    03-07-2019, 12:49 AM Go to last post
  14. Printing Problem, need some help.

    Started by apun77, 03-05-2019 05:25 AM
    • Replies: 1
    • Views: 224
    03-05-2019, 05:34 AM Go to last post
  15. Question Cura sending wrong instructions?

    Started by IAMspeedex, 02-28-2019 02:29 PM
    • Replies: 1
    • Views: 231
    02-28-2019, 02:59 PM Go to last post
  16. ender 3 not printing

    Started by elpiko, 02-26-2019 09:46 AM
    • Replies: 1
    • Views: 295
    02-26-2019, 03:50 PM Go to last post
  17. initial success...then failure

    Started by honerboys, 02-18-2019 03:26 PM
    • Replies: 6
    • Views: 649
    02-22-2019, 11:55 AM Go to last post
  18. MP Maker Select v2 Marlin Installation gone wrong

    Started by Pankh, 02-15-2019 11:10 PM
    • Replies: 1
    • Views: 226
    02-19-2019, 01:35 PM Go to last post

Page 1 of 147 1231151101 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •