Close



Page 1 of 22 12311 ... LastLast
Threads 1 to 20 of 423

Forum: RepRap Format Printer Forum

Discussion related to RepRap Format 3D Printers.

Sub-Forums Last Post

  1. Discussion related to Firmware Enhancements to Marlin.

    Forum Actions:

    Forum Statistics:

    • Threads: 43
    • Posts: 1,299
  2. Discuss related to Geetech 3D Printers

    Forum Actions:

    Forum Statistics:

    • Threads: 7
    • Posts: 26
  3. Discussion related to MakerFarm Prusa and PrintrBot 3D printers

    Forum Actions:

    Forum Statistics:

    • Threads: 829
    • Posts: 10,903
  1. Sticky Thread Sticky: Show your RepRap Printers

    Started by Larry, 10-09-2013 10:06 AM
    6 Pages
    1 2 3 ... 6
    • Replies: 57
    • Views: 62,482
    06-27-2017, 10:50 AM Go to last post
  2. Sticky Thread Sticky: RepRap Community - Introduce Yourselves

    Started by Eddie, 10-08-2013 01:34 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 66
    • Views: 54,976
    02-05-2017, 05:46 PM Go to last post
  1. Anet A8 home position below bed, past stop

    Started by dlwheeler, 11-14-2018 09:22 PM
    • Replies: 1
    • Views: 545
    11-16-2018, 07:16 AM Go to last post
    • Replies: 5
    • Views: 717
    11-05-2018, 09:54 AM Go to last post
  2. G-Code for filament retraction

    Started by iras, 10-25-2018 10:26 AM
    • Replies: 2
    • Views: 607
    10-27-2018, 05:05 PM Go to last post
    • Replies: 0
    • Views: 1,143
    09-01-2018, 05:51 PM Go to last post
    • Replies: 0
    • Views: 795
    09-01-2018, 04:31 PM Go to last post
  3. Anet A8 fan/extruder issue.

    Started by Kyle M., 05-05-2018 04:15 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 3,391
    08-25-2018, 10:06 PM Go to last post
    • Replies: 0
    • Views: 689
    08-08-2018, 09:46 PM Go to last post
  4. Prusa i3 Clone - Extruder Replacement

    Started by jmhecker, 07-31-2018 06:37 AM
    • Replies: 0
    • Views: 311
    07-31-2018, 06:37 AM Go to last post
  5. Hot end question

    Started by Paul6187, 12-08-2017 09:54 PM
    • Replies: 2
    • Views: 1,376
    07-24-2018, 08:34 AM Go to last post
  6. Test of Marlin 2.0.x - Good Results

    Started by LuckyImperial, 03-13-2018 11:24 AM
    • Replies: 4
    • Views: 3,472
    06-16-2018, 11:25 AM Go to last post
  7. Problem second print Bl touch

    Started by ryan34side, 05-31-2018 03:30 AM
    • Replies: 3
    • Views: 1,421
    05-31-2018, 12:31 PM Go to last post
  8. Need Recommendations for a simple non-contact Z-Axis probe

    Started by Roxy, 05-03-2016 06:41 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 5,190
    04-29-2018, 09:01 AM Go to last post
  9. Anet A8 issue

    Started by Kyle M., 04-25-2018 04:56 AM
    • Replies: 0
    • Views: 783
    04-25-2018, 04:56 AM Go to last post
    • Replies: 4
    • Views: 1,206
    04-04-2018, 08:26 AM Go to last post
  10. Anycubic Kossel Auto-Leveling Issues

    Started by gravspeed, 12-20-2017 11:45 AM
    auto level, kossel, problems
    • Replies: 1
    • Views: 2,402
    03-13-2018, 11:53 AM Go to last post
    • Replies: 3
    • Views: 1,595
    02-26-2018, 02:13 AM Go to last post
  11. Teebot Z Axis Offset Issue. Newbie Question

    Started by peterdawson, 02-03-2018 07:58 AM
    • Replies: 0
    • Views: 1,109
    02-03-2018, 07:58 AM Go to last post
  12. New 400x400x300 Printer

    Started by Chaparro1973, 09-18-2017 08:03 AM
    • Replies: 5
    • Views: 2,305
    12-26-2017, 11:06 AM Go to last post
  13. Pascoe and several theatrical

    Started by jumainsaew, 12-23-2017 09:50 AM
    • Replies: 0
    • Views: 1,050
    12-23-2017, 09:50 AM Go to last post
  14. The Shift Post Sandy Hook on

    Started by ristabondhon, 12-23-2017 09:49 AM
    • Replies: 0
    • Views: 855
    12-23-2017, 09:49 AM Go to last post

Page 1 of 22 12311 ... LastLast

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •