Close



Page 4 of 7 FirstFirst ... 23456 ... LastLast
Threads 61 to 80 of 128

Forum: CTC 3D Printers

Discussion related to CTC Duplicator/Bizer Printers

  1. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    2 Pages
    1 2
    • Replies: 11
    • Views: 67,640
    01-27-2018, 09:06 PM Go to last post
  1. Yet Another CTC Newbie - 2 1/2 questions.

    Started by adrianq, 04-29-2016 05:57 PM
    • Replies: 2
    • Views: 4,650
    05-04-2016, 02:25 PM Go to last post
  2. New CTC 3D owner

    Started by noiseboy72, 04-27-2016 04:49 PM
    • Replies: 5
    • Views: 4,900
    04-29-2016, 01:41 PM Go to last post
  3. Slic3r optimal gcode for CTC printet

    Started by tintalala, 04-27-2016 06:04 AM
    • Replies: 1
    • Views: 4,949
    04-28-2016, 09:02 PM Go to last post
  4. 20mm x 20mm test square is slighty off square

    Started by Raymo, 04-24-2016 12:20 PM
    • Replies: 4
    • Views: 4,755
    04-27-2016, 04:42 PM Go to last post
  5. Switched to Sailfish, but head is printing off the bed, not in middle.

    Started by Raymo, 04-10-2016 10:00 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 16,613
    04-18-2016, 05:40 AM Go to last post
  6. I just bought a CTC too..

    Started by Geoff, 03-10-2016 02:12 AM
    • Replies: 9
    • Views: 7,579
    04-11-2016, 05:33 PM Go to last post
    • Replies: 9
    • Views: 6,645
    04-10-2016, 09:48 AM Go to last post
  7. Bed temperature reading low - ABS lifting

    Started by d43d, 02-15-2016 12:47 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 16,634
    04-09-2016, 03:28 PM Go to last post
  8. ctc extruder wiring help

    Started by ozley, 04-05-2016 07:53 AM
    • Replies: 2
    • Views: 3,130
    04-05-2016, 09:32 PM Go to last post
  9. Nightmare start

    Started by d43d, 01-21-2016 05:21 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 47
    • Views: 61,243
    04-01-2016, 02:42 PM Go to last post
  10. X-Axis off by a few percent / Circles not round

    Started by noa, 03-26-2016 07:04 PM
    • Replies: 9
    • Views: 10,176
    03-31-2016, 12:17 PM Go to last post
  11. New CTC printer came broken

    Started by dspdrew, 02-27-2016 02:19 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 65,357
    03-23-2016, 04:46 AM Go to last post
  12. Filament refusing to feed.

    Started by dlps73, 03-01-2016 05:50 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 13,931
    03-19-2016, 09:37 AM Go to last post
  13. Shrinkage?

    Started by dlps73, 03-14-2016 04:35 PM
    • Replies: 4
    • Views: 3,544
    03-14-2016, 06:41 PM Go to last post
  14. Updating the board with a Atmega2560

    Started by TraxXavier, 03-06-2016 01:49 AM
    • Replies: 2
    • Views: 4,912
    03-07-2016, 11:52 AM Go to last post
  15. Extruder not reaching operating temp

    Started by err404, 02-19-2016 01:32 PM
    • Replies: 8
    • Views: 13,843
    02-20-2016, 11:56 AM Go to last post
  16. New CTC Owner

    Started by bigo93, 12-18-2015 08:40 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 52
    • Views: 58,820
    02-15-2016, 06:09 PM Go to last post
  17. CTC printer issue

    Started by stormy17, 02-14-2016 12:01 PM
    • Replies: 3
    • Views: 4,196
    02-15-2016, 08:17 AM Go to last post
  18. New nozzles

    Started by bigo93, 02-04-2016 12:12 PM
    • Replies: 2
    • Views: 5,670
    02-05-2016, 06:06 AM Go to last post
  19. Z Axis Offset

    Started by patele, 01-30-2016 08:37 AM
    • Replies: 4
    • Views: 6,291
    01-31-2016, 05:43 AM Go to last post

Page 4 of 7 FirstFirst ... 23456 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data