Close



Search:

Tag: firmware

Search: Search took 0.00 seconds.

  1. Has Anyone Experienced This Strange Movement?!

    Started by alielsayid, 06-27-2017 09:50 AM
    extruder, firmware, gcode, marlin
    • Replies: 1
    • Views: 627
    Last Post: 07-05-2017 02:31 PM
    by Roberts_Clif  Go to last post
  2. CUBE 3 Firmware HELP

    Started by Ale24x, 04-10-2017 11:44 PM
    cube, firmware
    • Replies: 3
    • Views: 1,087
    Last Post: 04-14-2017 12:14 PM
    by apoction  Go to last post
    • Replies: 2
    • Views: 1,051
    Last Post: 08-30-2017 06:46 AM
    by Roberts_Clif  Go to last post
  3. heater pin numbers

    Started by ohms, 01-28-2017 01:51 PM
    cartridge, firmware, heater, hotend, pins.h
    • Replies: 4
    • Views: 2,102
    Last Post: 01-28-2017 07:17 PM
    by ohms  Go to last post
    • Replies: 6
    • Views: 3,214
    Last Post: 06-12-2017 05:56 PM
    by Roberts_Clif  Go to last post
    • Replies: 4
    • Views: 2,650
    Last Post: 11-04-2016 01:58 PM
    by iDig3Dprinting  Go to last post
  4. Extruder temp reading is extremely inaccurate

    Started by iineviitable, 09-27-2016 09:37 PM
    firmware, temperature, thermistor
    • Replies: 2
    • Views: 1,762
    Last Post: 09-28-2016 04:11 PM
    by iineviitable  Go to last post
  5. HE 3D Delta printer - Firmware/Calibration

    Started by OriolFM, 09-05-2016 07:27 AM
    calibration, delta, firmware, he3d
    • Replies: 0
    • Views: 912
    Last Post: 09-05-2016 07:27 AM
    by OriolFM  Go to last post
  6. Marlin config error, can't figure this one out!!

    Started by CBPrints, 01-23-2016 11:07 PM
    config, error, firmware, marlin
    • Replies: 2
    • Views: 1,021
    Last Post: 01-24-2016 12:00 PM
    by CBPrints  Go to last post
  7. RADDS Info Thread

    Started by spaceorange12, 12-26-2015 08:56 PM
    arduino, due, firmware, radds, repetier
    • Replies: 9
    • Views: 4,132
    Last Post: 05-11-2016 10:26 AM
    by Roxy  Go to last post
  8. Printrboard scalability limitations?

    Started by wubwub, 12-24-2015 08:33 PM
    2 Pages
    1 2
    • Replies: 16
    • Views: 3,083
    Last Post: 12-26-2015 05:20 PM
    by wubwub  Go to last post
    • Replies: 0
    • Views: 424
    Last Post: 08-07-2015 08:24 PM
    by dirtythekid  Go to last post
  9. Is any Generation 3 Electronics user out there?

    Started by Traumflug, 07-27-2015 08:09 PM
    firmware, gen3, reprap, teacup
    • Replies: 0
    • Views: 859
    Last Post: 07-27-2015 08:09 PM
    by Traumflug  Go to last post
  10. MakerBot Replicator 5th Gen "Failed to print"

    Started by jdraughon, 07-21-2015 11:43 PM
    broken, error, firmware, makerbot 5th gen
    • Replies: 3
    • Views: 4,700
    Last Post: 07-22-2015 02:35 PM
    by MBSupport  Go to last post
  11. Rep. 2X Fan has stopped running. Help please.

    Started by ShapeFI, 07-06-2015 10:25 AM
    fan, firmware, makerbot replicator 2x, troubleshooting
    • Replies: 1
    • Views: 903
    Last Post: 07-06-2015 11:56 AM
    by MBSupport  Go to last post
  12. Replicator 2x Bricked?

    Started by EduTech, 07-02-2015 12:56 PM
    bricked, factory reset, firmware, replicator 2x
    • Replies: 2
    • Views: 1,771
    Last Post: 07-02-2015 05:48 PM
    by MBSupport  Go to last post
  13. Inverted Z-axis

    Started by 68x13, 04-21-2015 03:45 AM
    • Replies: 3
    • Views: 4,352
    Last Post: 05-20-2015 05:01 AM
    by 68x13  Go to last post
  14. Ramps 1.4 - Marlin 1.0.2 isues

    Started by avggrech, 02-17-2015 07:10 AM
    • Replies: 4
    • Views: 3,261
    Last Post: 02-19-2015 08:19 AM
    by avggrech  Go to last post
  15. Makerbot 5th Gen. - download old firmware

    Started by moe, 11-25-2014 08:56 AM
    bug, firmware, makerbot 5th gen
    • Replies: 0
    • Views: 1,234
    Last Post: 11-25-2014 08:56 AM
    by moe  Go to last post
  16. Prusa mendal I2 Pronteer face Marlin error

    Started by jakers181008, 11-12-2014 02:13 PM
    10 Pages
    1 2 3 ... 10
    • Replies: 90
    • Views: 18,388
    Last Post: 11-23-2014 01:37 PM
    by jakers181008  Go to last post
    • Replies: 395
    • Views: 96,082
    Last Post: 12-25-2016 08:05 AM
    by uncle_bob  Go to last post
  17. Fifth Gen issues...

    Started by cnashnow, 08-11-2014 03:45 PM
    firmware, makerbot 5th gen, self leveling, smart extruder
    • Replies: 3
    • Views: 2,754
    Last Post: 08-29-2014 11:56 AM
    by exit  Go to last post
Results 1 to 22 of 23