Close



Dig deeper, search our News website




Search:

Type: Posts; User: mjf55

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    448
    Views
    64,059

    This is an interesting read on print slant. Long...

    This is an interesting read on print slant. Long story short, it was his belts. http://forums.reprap.org/read.php?178,731246,page=1
  2. Thread: Mankati?

    by mjf55
    Replies
    2
    Views
    230

    Looks like the web site is working now.

    Looks like the web site is working now.
  3. Replies
    448
    Views
    64,059

    So Alexa seems to be ok at 0.24, but when does it...

    So Alexa seems to be ok at 0.24, but when does it start the slant? What if you just use the multiples of 8 at a thicker layer, say 0.48, is that an issue. This is a strange one.

    On your...
  4. Got me on that one. Care to translate?

    Got me on that one. Care to translate?
  5. Replies
    448
    Views
    64,059

    Get a speed square to double check. ...

    Get a speed square to double check.

    Remember, just because your paranoid, it doesn't mean they are not following you, or in your case, slanting when your not looking. ;-)
  6. Replies
    448
    Views
    64,059

    Post the pictures when you print them. Always...

    Post the pictures when you print them. Always interested in seeing results.
  7. Replies
    448
    Views
    64,059

    That how I start the calibration. 3 points and...

    That how I start the calibration. 3 points and manually level using the bed screws. Then by using the endstop correction, which in Repetier is measures in steps, I can make fine tune changes of...
  8. Replies
    448
    Views
    64,059

    OOPS 7 point. Basically followed this...

    OOPS 7 point. Basically followed this http://escher3d.com/pages/wizards/wizarddelta.php and this https://www.youtube.com/watch?v=tDLbqLve128 . It is all manual as you use manual controls/ gcode to...
  9. Replies
    448
    Views
    64,059

    Yeah, heat soak. Instructions say to heat bed to...

    Yeah, heat soak. Instructions say to heat bed to 110*c with a wet cloth on top of it for an hour. let it cool and do it again.

    Funny, the hotbed could not get past 90* with that wet cloth on...
  10. Replies
    27
    Views
    3,010

    Sticky: I just saw your PM. I re-downloaded the current...

    I just saw your PM. I re-downloaded the current version ( Jan20 ) from your page ( it worked, AVG did not complain ) and it installed correctly ( No AVG complaints. )
    Thanks for your updates to...
  11. Replies
    448
    Views
    64,059

    One at a time prints ok, but a pair causes a...

    One at a time prints ok, but a pair causes a slant, weird indeed. How does it look in the slicer, layer view prior to printing? If you pass me the STL and or the gcode, I will give it a shot on my...
  12. Replies
    448
    Views
    64,059

    I think I will invest in a couple SS nozzles,...

    I think I will invest in a couple SS nozzles, adding 0.5 into the mix. I do usually use 50*c for PLA. Thanks for the heads up for the nylon, but I do not see that material in my future.
  13. Replies
    448
    Views
    64,059

    Doesn't that take the shock absorption out of the...

    Doesn't that take the shock absorption out of the sprints? Is that a side purpose of the springs, or are they there just to level the bed?

    GOOD NEWS, Finally got my PrintBite today. Actually...
  14. Replies
    448
    Views
    64,059

    I had bed movement when I assembled mine, and I...

    I had bed movement when I assembled mine, and I tightened the screws anout half way. That did stop the movement.
  15. Replies
    448
    Views
    64,059

    So what do you think fixed it? Sounds strange to...

    So what do you think fixed it? Sounds strange to me.
  16. Replies
    448
    Views
    64,059

    Difficult to get, you bet, at least for me. ...

    Difficult to get, you bet, at least for me.
    Ordered on 11/27. He misplaced it in the end of year rush. Finally shipped Jan 8, 2018. Sat in Heathrow for a week. Now sitting in Kennedy . ...
  17. Replies
    27
    Views
    3,010

    Sticky: Si I tried downloading the latest Windows 64 bit...

    Si I tried downloading the latest Windows 64 bit installer from your web site, but AVG antivirus does not like it. This is what I get and it aborts the connection. It has never done this before. ...
  18. Replies
    7
    Views
    707

    So, first, I do not know of a definitive...

    So, first, I do not know of a definitive dictionary of phrases. Also, each slicer uses different terms. Yuck. Now , the air gap is exactly what it sounds like. It does try to print a little...
  19. I had this real bad on a large print (100x100mm)...

    I had this real bad on a large print (100x100mm) using S3D. First layer height was 150%, First Layer width was 125%. It was not present using Cura ( Initial Layer Line Width at 100%. What I do now...
  20. Replies
    7
    Views
    707

    Try adjusting the Raft Air Gap and the Initial...

    Try adjusting the Raft Air Gap and the Initial Layer Z Overlap settings. They are in the Build Plate Adhesion section. If they are not visible when Raft is selected, press the settings icon ( gear)...
  21. My want to try green Frog Tape. That is what I...

    My want to try green Frog Tape. That is what I use and it adheres ( the tape that is ) to the bed better than blue tape. Prints adhere to the tape fine.
  22. Replies
    27
    Views
    3,010

    Sticky: Just downloaded, AVG doing a 3 minute review. ...

    Just downloaded, AVG doing a 3 minute review. Thanks

    EDIT, well AVG taking its time, but I ran it anyway. Wire Frame looks nice. Great job.
  23. By your own admission ( your post) 1- Cura...

    By your own admission ( your post)
    1- Cura already corrected the issue in later releases.
    2- changing orientation will also correct, but adds an hour to the print time.

    3D printing is not...
  24. Replies
    448
    Views
    64,059

    So, any update on BB? Oh, Still no Printbite. ...

    So, any update on BB?

    Oh, Still no Printbite. Ordered on 11/27. Took 2 week to 'process' Still did not arrive here. Cant seem to get the tracking # from Flex3d. They are not the best at...
  25. Replies
    27
    Views
    3,010

    Sticky: Got that AVG message again on the newest version....

    Got that AVG message again on the newest version. They will let me know in a 143 minutes. I told it (AVG) to run it anyway (I hope I am right). Looks good. I did not have any issues with the first...
Results 1 to 25 of 178
Page 1 of 8 1 2 3 4