Close



Search:

Type: Posts; User: Roxy

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    447

    If you have the source files... Or even just...

    If you have the source files... Or even just the Configuration.h and Configuration_adv.h files... You have everything you need.
  2. You can use G92 to set the current coordinate...

    You can use G92 to set the current coordinate values. For example... After the machine goes to Z=15.0mm you could do a G92 Z15.25 to move the nozzle closer to the bed.
  3. Replies
    15
    Views
    6,544

    Sticky: The way Marlin works is if the EEPROM is enabled,...

    The way Marlin works is if the EEPROM is enabled, it fetches all its values from the EEPROM. So, when you first turn on the EEPROM capability, you need to do a M502 to load the values specified in...
  4. Replies
    15
    Views
    6,544

    Sticky: M499 is not an officially supported GCode. If...

    M499 is not an officially supported GCode. If you add the code to your firmware it will work. But, you don't really need it to get your firmware's EEPROM updated. Its just a 'Nice to Have'.
  5. Replies
    7
    Views
    721

    About the only good thing about Simplify-3D is it...

    About the only good thing about Simplify-3D is it works with Marlin.
  6. Are you running Marlin? If so... you might...

    Are you running Marlin? If so... you might want to try relaxing the thermal run away numbers in configuration_adv.h

    Those parameters are set to be pretty safe. But they might be tighter than...
  7. Replies
    8
    Views
    1,079

    This is not true. Turn on #define BABYSTEPPING...

    This is not true. Turn on
    #define BABYSTEPPING and
    #define DOUBLECLICK_FOR_Z_BABYSTEPPING
    in Configuration_adv.h

    And if you want... You can baby step any of the 3 axis from the LCD menu...
  8. Replies
    8
    Views
    1,079

    Can you post your modified pins.h file here? Or...

    Can you post your modified pins.h file here? Or at https://github.com/MarlinFirmware/Marlin/issues would be OK too. With a modified pins.h file that is working for you... It should not be too...
  9. Replies
    8
    Views
    1,079

    Is the pins.h file wrong? The RAMPS pin file is...

    Is the pins.h file wrong? The RAMPS pin file is probably the best tested one. 1/2 of the people use that one. If it has an error in it... We need to get that fixed ASAP.
  10. Replies
    31
    Views
    4,702

    Yeah... Those mesh number look good. You won't...

    Yeah... Those mesh number look good. You won't have a problem getting good adhesion with your first layer. Also... If you turn on the Z-BabyStepping and Double-Click-for-Babystepping, it...
  11. Replies
    31
    Views
    4,702

    The Topology map is probably correct. Try to...

    The Topology map is probably correct. Try to level the bed using the command up above. And then proceed with the mesh generation using G29 P1
    We can make it work with what you have. But if...
  12. Replies
    31
    Views
    4,702

    You have a 1.0 mm tilt from left to right. UBL...

    You have a 1.0 mm tilt from left to right. UBL can handle that. But you will get better results if you physically level your bed. You can use G29 P1 U T to get points spread out on the outside...
  13. Replies
    31
    Views
    4,702

    What happens when you do a G29 P1 ? If it...

    What happens when you do a G29 P1 ? If it completes, do a G29 T and post the results. The 50mm X_PROBE_OFFSET_FROM_EXTRUDER is rather extreme. But depending on what we see in the T opography...
  14. Replies
    31
    Views
    4,702

    If you had a RAMPS board I could tell you where...

    If you had a RAMPS board I could tell you where to put the volt meter and what to crank the numbers up to. But most electronics boards let you control the stepper motor current. You can crank that...
  15. Replies
    31
    Views
    4,702

    It is typical to have to adjust your servo angles...

    It is typical to have to adjust your servo angles slightly from what ever the manufacturer has set. The reason is the probe leg servo horn has teeth on it... It can only go in certain positions. ...
  16. Replies
    31
    Views
    4,702

    You can use the M280 command to verify what your...

    You can use the M280 command to verify what your angles should be. Probably those are wrong in you Configuration.h file

    Do a M280 P0 S90 to set the servo to 90 degrees. Try the two angles in...
  17. Replies
    57
    Views
    45,991

    Sticky: That is not a picture of 'Your' printer. That is...

    That is not a picture of 'Your' printer. That is a picture of a product being reviewed.
  18. Replies
    10
    Views
    1,676

    Once you get a portion of the G26 to print OK... ...

    Once you get a portion of the G26 to print OK... The process is simple. Move the nozzle to areas that are bad, and edit them. Don't try to get it perfect the first time. Just get it better. ...
  19. Replies
    10
    Views
    1,676

    One thing you can do is change your Z_MAX height...

    One thing you can do is change your Z_MAX height by 10 mm... Do a M502 & M500... And see if G26 is 10mm above the bed... If it is not... It maybe you have that number set wrong. G26 just...
  20. Replies
    10
    Views
    1,676

    Is that using Repetier Host? Maybe doing a...

    Is that using Repetier Host? Maybe doing a G29 T1 won't drop as many characters?

    But I think you can continue... The numbers do not look crazy.

    You do have the bed very level.

    If...
  21. Replies
    10
    Views
    1,676

    Also... you should first verify you can print a...

    Also... you should first verify you can print a small item at the center of your bed without any bed leveling active. Usually, when these types of difficulties show up trying to bring up a bed...
  22. Replies
    10
    Views
    1,676

    UBL now works with Delta printers. (oldmcg did...

    UBL now works with Delta printers. (oldmcg did the work to get it running in that environment.) A good place to start would be showing us your bed's Topography make. Do a G29 T and post the...
  23. Replies
    31
    Views
    4,702

    It doesn't matter what bed leveling system you...

    It doesn't matter what bed leveling system you are trying to bring up... Make sure you can print a small calibration cube at the center of your bed with no bed leveling active. Make sure you can...
  24. If you bring up the UBL Bed Leveling System, the...

    If you bring up the UBL Bed Leveling System, the accuracy of the Z-Probe doesn't really matter. If the probe is super accurate, it save 10 or 15 minutes of setup time. But even with a horrible...
  25. If you have Repetier firmware.... You don't have...

    If you have Repetier firmware.... You don't have Marlin. If you had Marlin firmware, I could help you.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4