Close



Search:

Type: Posts; User: Roberts_Clif

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    344

    I Bought Every episode thru 6 Have only watch...

    I Bought Every episode thru 6 Have only watch about Half so Far.

    OK lets take a look at your numbers
    18:15:23.553 : N17 M501*17
    18:15:23.610 : echo:V39 stored settings retrieved (465 bytes; crc...
  2. Replies
    10
    Views
    344

    Hello 3Dave Post Printer Image Here, Let's...

    Hello 3Dave

    Post Printer Image Here, Let's get this 3D Printer Working for you.
  3. Replies
    10
    Views
    344

    Finally found it here...

    Finally found it here you can also take a look maybe more information not in the other one.


    Marlin-1.1.0-RC6 Hic

    This gives Three Hictop compatible Marlins that compile With out errors on...
  4. Replies
    10
    Views
    344

    So you want to do // M500 - stores parameters...

    So you want to do

    // M500 - stores parameters in EEPROM
    // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
    // M502 - reverts to the default...
  5. Replies
    10
    Views
    344

    If this is a Hictop 3DP12 this line should be ...

    If this is a Hictop 3DP12 this line should be

    #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 2560, 94.4962144}
  6. Replies
    10
    Views
    344

    I have never seen the marlin-conf editor. I have...

    I have never seen the marlin-conf editor. I have looked for but have, only found this Prusa Calculator. I will be sure to give it a try.
  7. Replies
    10
    Views
    344

    I have 2 Hictops Aluminum 3D Printers and have...

    I have 2 Hictops Aluminum 3D Printers and have tried to compile Marlin 1.1.4 without any success.

    I have been running Marlin-1.1.0-RC8BF-HICi3 on both of my Hictop 3D Printers.

    You can download...
  8. Replies
    8
    Views
    366

    I Prefer Fusion 360 Download Enthusiast (Free...

    I Prefer Fusion 360 Download Enthusiast (Free), (Every Year Free licensing here)

    This Is one of the Best Free programs I have downloaded since They released Toonz for Free.
  9. Replies
    3
    Views
    245

    I would suggest measuring the Power supply...

    I would suggest measuring the Power supply voltage while Heating Hot-bed an Hot-end.
    If the power on the supply is not 12volt or better power supply is may not be adequate. If 12Volts then.
    If the...
  10. Replies
    7
    Views
    484

    Soft solder typically has a melting point range...

    Soft solder typically has a melting point range of 90 to 450 C
    Most believe solder is solder incorrect. There are many different kinds of solder Kesler high temp is the best Solder to use for your...
  11. Replies
    1
    Views
    189

    You can measure the Resistance of the Hot-end it...

    You can measure the Resistance of the Hot-end it should be between 2-20 ohms. If you do not have a meter a cheap one is about $10 at every auto parts store.
    The wire size is a big deal and many...
  12. No need for a Showdown. There will always be...

    No need for a Showdown. There will always be different opinions it does not mean one is wrong and one is right, they are merely different..

    I have always printed with Nozzle 190-198C, bed temp of...
  13. Actually that print was way too close to the bed,...

    Actually that print was way too close to the bed, I was showing how secure you could get your prints on Vinyl Transfer Paper.
    When adjusted up a little higher the prints come off with a couple...
  14. Replies
    15
    Views
    5,948

    Sticky: Please Explain how this M499 works then so I can...

    Please Explain how this M499 works then so I can write it down.
  15. Replies
    15
    Views
    5,948

    Sticky: Hello I look in the G-Code and M-Code Grand...

    Hello

    I look in the
    G-Code and M-Code Grand Master List

    M499 is not on the list.

    https://softsolder.com/2013/03/14/g-code-and-m-code-grand-master-list/
  16. Replies
    7
    Views
    484

    The CR-10 is a 12 Volt 3D Printer

    The CR-10 is a 12 Volt 3D Printer
  17. I would remove all kapton tape from the bed clean...

    I would remove all kapton tape from the bed clean with goof off, then 70% alcohol. Then I would buy a sample roll of Vinyl Transfer Paper Tape.
    Most any brand will work as long as it is paper would...
  18. I printed a model on a sheet of paper, if you...

    I printed a model on a sheet of paper, if you roll the paper under the print model paper comes right off.

    On larger prints, I could not keep the single sheet paper flat enough clipped or taped to...
  19. Replies
    2
    Views
    393

    It appears he's advertising this 3D Printing...

    It appears he's advertising this 3D Printing Service in Banh Van Tran, Tan Binh Dist. Ho Chi Minh City, Vietnam.
    Though no one would complain if prices dropped. That would just mean more 3D Printers...
  20. Could be a simple as replacing your USB cable, or...

    Could be a simple as replacing your USB cable, or Configuring your slicer to the correct baud-rate and serial port.

    If you could give us more information about your setup it will be easier to...
  21. Hello, Like your 3D Printing system...

    Hello,

    Like your 3D Printing system ingenious.

    Like you I too had EFI problems, It started when I purchased a 2nd 3D Printer that was 24volt Hictop 3DP12.
    I solved you EFI troubled by 3D...
  22. If you need help setting up Cura simply ask ...

    If you need help setting up Cura simply ask

    Posting a picture of the error you get. will help you solve your problem.
  23. 3D Printer SD Cards are formatted in Fat, so what...

    3D Printer SD Cards are formatted in Fat, so what size is your SD card.

    Your 3D Printer may not recognize the SD Card if it is too large
  24. Replies
    1
    Views
    251

    I have good prints and I have bad prints with my...

    I have good prints and I have bad prints with my Build surface. It seems that they have to be adjusted to it their own G-Spot that your printer likes.

    It also helps to clean the Bed with 70%...
  25. Try putting "G92 E0" in your start code... before...

    Try putting "G92 E0" in your start code... before G28
Results 1 to 25 of 65
Page 1 of 3 1 2 3