Close



Search:

Type: Posts; User: Roxy

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    276

    Once you get a portion of the G26 to print OK... ...

    Once you get a portion of the G26 to print OK... The process is simple. Move the nozzle to areas that are bad, and edit them. Don't try to get it perfect the first time. Just get it better. ...
  2. Replies
    10
    Views
    276

    One thing you can do is change your Z_MAX height...

    One thing you can do is change your Z_MAX height by 10 mm... Do a M502 & M500... And see if G26 is 10mm above the bed... If it is not... It maybe you have that number set wrong. G26 just...
  3. Replies
    10
    Views
    276

    Is that using Repetier Host? Maybe doing a...

    Is that using Repetier Host? Maybe doing a G29 T1 won't drop as many characters?

    But I think you can continue... The numbers do not look crazy.

    You do have the bed very level.

    If...
  4. Replies
    10
    Views
    276

    Also... you should first verify you can print a...

    Also... you should first verify you can print a small item at the center of your bed without any bed leveling active. Usually, when these types of difficulties show up trying to bring up a bed...
  5. Replies
    10
    Views
    276

    UBL now works with Delta printers. (oldmcg did...

    UBL now works with Delta printers. (oldmcg did the work to get it running in that environment.) A good place to start would be showing us your bed's Topography make. Do a G29 T and post the...
  6. Replies
    12
    Views
    1,605

    It doesn't matter what bed leveling system you...

    It doesn't matter what bed leveling system you are trying to bring up... Make sure you can print a small calibration cube at the center of your bed with no bed leveling active. Make sure you can...
  7. If you bring up the UBL Bed Leveling System, the...

    If you bring up the UBL Bed Leveling System, the accuracy of the Z-Probe doesn't really matter. If the probe is super accurate, it save 10 or 15 minutes of setup time. But even with a horrible...
  8. If you have Repetier firmware.... You don't have...

    If you have Repetier firmware.... You don't have Marlin. If you had Marlin firmware, I could help you.
  9. Bowden drive causes a number of issues. The only...

    Bowden drive causes a number of issues. The only benefit you get is slightly less weight at the nozzle. But for all of the extra issues that come up, I'm just not a fan of Bowden drive.
  10. Replies
    12
    Views
    1,605

    In the Rambo pins file, it says... // //...

    In the Rambo pins file, it says...

    //
    // Servos
    //
    #define SERVO0_PIN 22 // Motor header MX1
    #define SERVO1_PIN 23 // Motor header MX2
    #define SERVO2_PIN 24 // Motor...
  11. Replies
    12
    Views
    1,605

    Yikes! I didn't know the Rambo board did not...

    Yikes! I didn't know the Rambo board did not have servo connectors on it. That really limits where it can be used!
  12. Replies
    12
    Views
    1,605

    It looks like the servo's are turned on. (for...

    It looks like the servo's are turned on. (for one servo). You should be able to do a M280 P0 S45 or M280 P0 S90 to move the servo if it is plugged into the servo 0 connector.
    You need power for...
  13. A G29 W will tell you What G29 thinks about the...

    A G29 W will tell you What G29 thinks about the world. Very early in the G29 W report, you will see what it thinks about a Fade Height. But if you lower the nozzle down to 1mm above the bed,...
  14. No! Stay with bugfix_v1.1.0 That has a lot of...

    No! Stay with bugfix_v1.1.0 That has a lot of good stuff that is not in v1.1.0 Please put bugfix_v1.1.0 back on your machine. And do the 'Quick Start' sequence here:
    (You can skip the...
  15. Well... It depends on how you want the system to...

    Well... It depends on how you want the system to operate. I want the bed leveling system alive and working when the machine powers up. If you want that behaviour, you do a G29 S1 to save your...
  16. Replies
    3
    Views
    868

    Ah.... Yeah... But you probably want to run...

    Ah.... Yeah... But you probably want to run BugFix_v1.1.0 That is the most 'correct'.
    We had an OctoPrint bug right out of the shoot and a few more things have been made better.



    To...
  17. Replies
    7
    Views
    835

    One thing you can try is get the nozzle hot... ...

    One thing you can try is get the nozzle hot... More like ABS temperature instead of PLA. And use those little nozzle cleaning wire things that welders use to clean their torches. I have pushed...
  18. Have you looked at the GCode file you are trying...

    Have you looked at the GCode file you are trying to print? Are there extra G28's in that?
  19. Replies
    7
    Views
    1,219

    It will get a 'Tag' at...

    It will get a 'Tag' at https://github.com/MarlinFirmware/Marlin/tree/ I'm not sure what that Tag will be, but it is very possible it will be https://github.com/MarlinFirmware/Marlin/tree/1.1.0 ...
  20. You can switch away from the web browsers that...

    You can switch away from the web browsers that don't work for you....
  21. Replies
    7
    Views
    1,219

    1. Look for AUTO_BED_LEVELING_UBL in the...

    1. Look for AUTO_BED_LEVELING_UBL in the Configuration.h file. Turn it on and adjust the numbers in that section to reasonable values for your printer.

    2. The bed orientation never made it...
  22. Replies
    7
    Views
    1,219

    You do need to bring up your old Configuration.h...

    You do need to bring up your old Configuration.h files in a visual diff program and cross over the important settings. I know this is a hassle. But some of the names had to be changed to make...
  23. Agreed... But Open Source provides a very good...

    Agreed... But Open Source provides a very good proving ground for new ideas. Anybody can fork the code base and develop their concept. If the idea is good, it can be re-absorbed into the main...
  24. Your link doesn't work. So it is hard to find...

    Your link doesn't work. So it is hard to find out more about the printer in your picture. But I can tell you this much: It is a Prusa i3 Open Source derivative. And that means there is a...
  25. Thread: Marlin version

    by Roxy
    Replies
    4
    Views
    910

    Ah... I'm not sure how to answer. There are so...

    Ah... I'm not sure how to answer. There are so many i3's. And Prusa has his own fork of Marlin for his current i3's.

    But if you want to bring up a generic i3, you want to do it using...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4