Close



Search:

Type: Posts; User: wirlybird

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4,046
    Views
    523,720

    Sticky: They are just starting to ship. I don't know...

    They are just starting to ship. I don't know when it will come but it will be no time soon to install. Busy starting a build on a larger volume printer.
  2. Replies
    4
    Views
    238

    I would say it is a bad or miss-wired power...

    I would say it is a bad or miss-wired power supply. Could be a pinched wire somewhere. I'd see if you can get a new supply out of them. Otherwise you're going to want to search every wire to make...
  3. Replies
    4
    Views
    238

    Could be as simple as a pinched wire somewhere. ...

    Could be as simple as a pinched wire somewhere. What is the "shock" like? A tingling low voltage type like touching a 9v battery to your tongue or more substantial? If it is a substantial shock...
  4. Run at 230 to start. Drop bed to 100 or 95 after...

    Run at 230 to start. Drop bed to 100 or 95 after first layer or go down to that 1 layer at a time.
    Extrusion multiplier at 1.0
    Infill at 20%
    Reduce overlap to 25
    Retraction 1.2 at 1800mm/min to...
  5. Replies
    3
    Views
    863

    See if coast or wipe is on and change it and see.

    See if coast or wipe is on and change it and see.
  6. Replies
    4,046
    Views
    523,720

    Sticky: Interesting. On the X-one the Prusa Colorprint...

    Interesting. On the X-one the Prusa Colorprint app might work since it is gcode based. I may have to try it.

    I have wanted a way to easily do it on the Tech-1 of a FFCP.
  7. Replies
    1
    Views
    228

    Check out QIDI 3D on facebook. Someone may have...

    Check out QIDI 3D on facebook. Someone may have put files there.
  8. Try reducing the mesh before exporting.

    Try reducing the mesh before exporting.
  9. What are your settings? Speed, layer etc. You...

    What are your settings? Speed, layer etc.

    You can cool down a bit to 230. Turn off any part cooling fan if there is one. What brand of ABS?

    You are getting irregular cooling of the part. ...
  10. Replies
    4,046
    Views
    523,720

    Sticky: Yea, PLA+ is just stronger PLA. So it is nice to...

    Yea, PLA+ is just stronger PLA. So it is nice to print and prints great at 215 and a tougher product. I go to PTEG or ABS for higher temp and tough and it is still cost effective.

    I had a...
  11. Replies
    4,046
    Views
    523,720

    Sticky: Like those fixes. Now to go stock up on fuses. ...

    Like those fixes. Now to go stock up on fuses.

    I sent back 6 rolls to MG. Filament diameters where way off. I had 1.67 to 1.78 on some and as much as 1.83 on some. I am doing there monthly box...
  12. Replies
    4,046
    Views
    523,720

    Sticky: Nice one! I was printing along last night and...

    Nice one!

    I was printing along last night and came back to a dark printer! No power. I thought well, it has worn out. It has printed a lot in a year. It is about to get some upgrades so I...
  13. Replies
    4,046
    Views
    523,720

    Sticky: They were pretty quick for me on one. I think...

    They were pretty quick for me on one.
    I think you could do PLA ok. May take some work. Google PLA and no heated bed.
  14. Replies
    5
    Views
    769

    I have to agree with CA on this one. Frustration...

    I have to agree with CA on this one. Frustration is easy to understand. I'd hound B&H first to see what they have to say about it.
  15. Replies
    4,046
    Views
    523,720

    Sticky: Also check ebay for QIDI the part is cheap.

    Also check ebay for QIDI the part is cheap.
  16. Replies
    4,046
    Views
    523,720

    Sticky: Ha, with a choice like that I think you are...

    Ha, with a choice like that I think you are definitely a music person.

    I don't think it is anything to worry about. I have honestly never realized it made a noise.
  17. Replies
    4,046
    Views
    523,720

    Sticky: Can you name that tune in 4 notes or less?

    Can you name that tune in 4 notes or less?
  18. Replies
    4,046
    Views
    523,720

    Sticky: Is the parts cooling fan coming on. I had this...

    Is the parts cooling fan coming on. I had this recently that it was set to come on and I didn't realize and the left side of an ABS print lifted. Turned it of and redid the part and it was fine.
    ...
  19. Replies
    4,046
    Views
    523,720

    Sticky: As a side note I am having a bad time with...

    As a side note I am having a bad time with solutech PLA. Seems very inconsistent in size.
  20. Search Flexion's site for their filament unload...

    Search Flexion's site for their filament unload gcode and it may be a good example to reverse engineer to use it to load. If I can find it later I will attach. Had it but never needed to use it.
  21. This is much better. ...

    This is much better. http://www.flashforge.com/support-center/
    The other spot is a mess.

    The other one would probably be ok to install and let it update but this is the most recent version. ...
  22. Obviously you are getting bad info. Flashprint...

    Obviously you are getting bad info. Flashprint is made by Flashforge for ALL of their printers. It comes with the Flashforge Creator Pro. I have used it and it is fine.

    As far as the gcode, you...
  23. Replies
    1
    Views
    334

    Something has shorted out. Probably the power...

    Something has shorted out. Probably the power supply. If the cord came with it try a different one but otherwise I wouldn't mess with it until you get someone with some electrical/electronics...
  24. Extrusion multiplier is usually recommended to be...

    Extrusion multiplier is usually recommended to be changed in measures of .05 and really not more than .1. So the first thing you have to do is get the filament size as close as possible. The...
  25. That really makes no sense. You are having...

    That really makes no sense. You are having issues now but don't want to try a free slicer made for Flashforge that might work for you. S3D is good but it is still $150.

    Seems to me you would...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4