Close



Search:

Type: Posts; User: Roxy

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Bed Crash on G29

    by Roxy
    Replies
    1
    Views
    141

    What type of bed leveling are you using? What...

    What type of bed leveling are you using? What version of the firmware are you having problems using? Have you changed anything recently?

    If you are using an old version of the firmware, it...
  2. Replies
    8
    Views
    379

    If you are a RepRap'er... Everything is "Open...

    If you are a RepRap'er... Everything is "Open Source". Mostly I like developing firmware, so the Marlin firmware is good for me. And I'm taking off on a ski trip tomorrow. I'll be...
  3. Replies
    65
    Views
    3,528

    You can turn the dial to adjust that number up or...

    You can turn the dial to adjust that number up or down. It is the 'Feed Rate'. You can make the printer go faster or slower by turning the dial.
  4. Replies
    65
    Views
    3,528

    I have always used Rave's 4x Mega hairspray. ...

    I have always used Rave's 4x Mega hairspray. Also available at Walmart. It works very good! But I'm going to pick up a can of Garnier Fructis Super Hold 5 and see if I can tell a difference.
  5. Thread: Thermal Runaway

    by Roxy
    Replies
    3
    Views
    199

    It doesn't seem to me that installing different...

    It doesn't seem to me that installing different fans would cause a Thermal Runaway problem. But... I can tell you I always relax Marlin's thermal runaway parameters.

    I'm not comfortable...
  6. Replies
    5
    Views
    410

    As an FYI: When I change filament... I extrude...

    As an FYI: When I change filament... I extrude (slowly) until the filament comes out at a uniform rate and appearance. It depends on your printer. But most printers once the filament fills the...
  7. Replies
    5
    Views
    410

    There are a lot of variables. But I've never...

    There are a lot of variables. But I've never had an 'Enclosure' and I get perfect adhesion across 100% of my 400mm x 400mm bed every time. Try bringing up the UBL code at:
    ...
  8. ssayer... I agree. But what I'm struggling to...

    ssayer... I agree. But what I'm struggling to understand is how this has anything to do with 3D-Printing.
  9. Replies
    38
    Views
    4,442

    This hasn't been discussed lately (in the last...

    This hasn't been discussed lately (in the last few months). But the plan was to get RC8 promoted to 'Stable' and then no more features would be added to it. Only bug fixes. And at that time, the...
  10. Replies
    6
    Views
    523

    The source code for your firmware should be...

    The source code for your firmware should be posted. If you look in the Configuration.h and Configuration_adv.h file, those #define's control just about everything.
  11. Replies
    11
    Views
    2,100

    Yeah... I don't understand why they refuse to be...

    Yeah... I don't understand why they refuse to be standard and put the X Axis endstop on the left side and plug it into the X-Min pin. That makes no sense other than that is how they finally got...
  12. Replies
    62
    Views
    5,118

    Torby, you can fix that wrap by putting some...

    Torby, you can fix that wrap by putting some slits in your box. The wrap is caused by the plastic shrinking as it cools and eventually, with enough layers, it pulls up off the bed. One answer is...
  13. Replies
    11
    Views
    1,061

    Of course this is just personal opinion. But a...

    Of course this is just personal opinion. But a power supply is just 'Electronics'. If it isn't being stressed past its specification, it should last 'indefinitely'. It shouldn't wear out. It...
  14. Thread: Help X axis stops

    by Roxy
    Replies
    3
    Views
    438

    Is the X Axis getting too much power and the...

    Is the X Axis getting too much power and the driver chip entering thermal protection shutdown mode? After it stops, does it start moving after a few minutes?
  15. Yes... Your understanding is correct. And...

    Yes... Your understanding is correct. And incidentally, the BL-Touch stuff was added after UBL forked from RC-7. So you can use a BL-Touch with UBL, but you have to set it up as manually instead...
  16. Replies
    155
    Views
    30,221

    Yes! That is definitely a good thing to add to...

    Yes! That is definitely a good thing to add to the example_configurations directory. Can you make a Push Request for them to be added?
  17. It works. But the RC-8 / RCBugFix version does...

    It works. But the RC-8 / RCBugFix version does not allow you to save the mesh. The UBL Branch lets you save the mesh and it also provides very nice Mesh Validation Pattern and Editing commands...
  18. Replies
    12
    Views
    1,116

    How do you know the temperature varies that much?...

    How do you know the temperature varies that much? Are you printing on glass? Is the glass making good contact with the entire heat bed? If it is not, the heat bed will be warmer in those...
  19. For sure... RC-8 is much better than RC-7. ...

    For sure... RC-8 is much better than RC-7. But you really should be using RCBugFix. Right now, RCBugFix is very close to RC-8. But over time... RCBugFix will be much better than RC-8.
  20. Replies
    6
    Views
    708

    I've had similar results with dirty filament. I...

    I've had similar results with dirty filament. I had a roll that just sat around for a long time and had a thin film of dust on it. It printed fine for a while, but then the dust started to...
  21. Thread: Is Forum hacked?

    by Roxy
    Replies
    17
    Views
    2,221

    This is speculation, but my guess is a lot of...

    This is speculation, but my guess is a lot of them have alcohol as a 'contributing' factor.
  22. Replies
    155
    Views
    30,221

    RAMPS is much more standard. I'm in the process...

    RAMPS is much more standard. I'm in the process of converting all of my printers over to RAMPS. Probably if you post an issue at https://github.com/MarlinFirmware/Marlin/issues somebody will have...
  23. Replies
    155
    Views
    30,221

    These features are now fully enabled and...

    These features are now fully enabled and working....
  24. Hopefully you got the extra meter of 2020...

    Hopefully you got the extra meter of 2020 aluminum so you can do a nice filament roller. And if you got the 20x4 LCD Screen, I have the .STL files to make a nice case that clips onto the top rail. ...
  25. No. Of course not. I'm just very happy with my...

    No. Of course not. I'm just very happy with my FT-i3-2020. And up until 3 or 4 weeks ago... It was the development platform for Marlin's new Automatic Bed Leveling System. ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4