Close



Dig deeper, search our News website




Search:

Type: Posts; User: gmay3

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    19,316

    haha no problem at all! Hope your enjoy it!

    haha no problem at all! Hope your enjoy it!
  2. Replies
    4
    Views
    19,316

    Was it this one? :rolleyes:...

    Was it this one? :rolleyes:
    https://www.thingiverse.com/thing:438960
  3. Replies
    3
    Views
    3,488

    That's a great idea curious aardvark! I swapped...

    That's a great idea curious aardvark! I swapped my Y and extruder motors and what I found was really funny. I had rotated the printer so I could work on the Ramps boards and the new perspective...
  4. Replies
    3
    Views
    3,488

    Extruder stepper motor failure

    Hey guys, I ended up just buying Simplify3D and noticed (don't think it's related) that my extruder motor is no longer turning during a print. When I heat up the hotend and manually turn the gears...
  5. Replies
    11
    Views
    7,675

    Finally got around to making this firmware change...

    Finally got around to making this firmware change and it works perfectly! No more jitter, thanks so much kd7eir!
  6. Replies
    11
    Views
    7,675

    kd7eir, thanks again my ABL is working now and it...

    kd7eir, thanks again my ABL is working now and it is awesome!

    I've noticed that my probe servo will chatter back and forth a little while travelling in the Z direction down to the bed. Is this...
  7. Replies
    11
    Views
    7,675

    Thanks for the link kd7eir! I'll check it out....

    Thanks for the link kd7eir! I'll check it out. Appreciate the help!
  8. Replies
    11
    Views
    7,675

    Update: Commented out safe homing worked like a...

    Update: Commented out safe homing worked like a charm, thank you guys! My hotend is homing in the typical back left corner of the bed.

    New question: I tried a first print after sending a G28 and...
  9. Replies
    11
    Views
    7,675

    Thanks everyone! I'll give that a shot and I'll...

    Thanks everyone! I'll give that a shot and I'll update with the results.
  10. Replies
    5
    Views
    6,691

    Make sure your X/Y carriage belts are tight, any...

    Make sure your X/Y carriage belts are tight, any slop in the axes can cause a slight shift in layers will null the appearance of 50 micron printing, making it looks like a lower resolution! Good...
  11. Replies
    5
    Views
    4,807

    I agree with what everyone has said above. My...

    I agree with what everyone has said above. My stongest feeling is that there is overextrusion, I'm guessing that these were printed solid or close to it (given the small size of the cubes and amount...
  12. Replies
    5
    Views
    13,995

    Hey DrMacZed, which printer do you have? I...

    Hey DrMacZed, which printer do you have?

    I have a 8inch i3v that does not have a heating bed relay. Mine has always shut both the hot end and bed down after printing.
  13. Replies
    11
    Views
    7,675

    ABL Home Position Question

    Hey everyone! After almost a year of having the parts to do so, I've finally followed the ZennmasterM ABL tutorials and have ABL "working"!

    For some reason, I can't figure out why my G28 home...
  14. Replies
    3
    Views
    3,280

    This probably isn't the solution but check your...

    This probably isn't the solution but check your idlers and rails for any debris. If the idler wheels have to "speed bump" over something you get an equal bump in the same place throughout the whole...
  15. Replies
    0
    Views
    2,223

    Support with Support

    Hey all! It's been far too long, hope you have all been well!

    I was wondering if anyone was having good luck with their support printing in slic3r? I can't seem to get the settings right to allow...
  16. Thread: Layer Shift

    by gmay3
    Replies
    6
    Views
    6,038

    Hey BLKKROW, I've had this happen to me before....

    Hey BLKKROW, I've had this happen to me before. Check the set screws on your x axis GT pulleys (the toothed belt gears). When the length of time the print is going increases, things start heating up...
  17. Replies
    6
    Views
    3,745

    Ye olde hardware store glass. I also can't...

    Ye olde hardware store glass.

    I also can't even remember when I last cleaned it or resprayed hairspray on it. From my experience so far I feel that bed adhesion more about the right amount of...
  18. Thread: Nozzle height?

    by gmay3
    Replies
    5
    Views
    3,811

    Hey DrBoost, I would say leave a gap that is...

    Hey DrBoost, I would say leave a gap that is about 60-80 percent of the layer thickness you're going to be printing at. For example when printing at .2mm I use a .127mm feeler gauge.

    Hope this...
  19. Replies
    12
    Views
    5,956

    dunginhawk, don't disable the hexagon cooling...

    dunginhawk, don't disable the hexagon cooling fan, it could cause your extruder parts to melt and deform. Instead flip the fan direction by removing it and flipping it around so it pulls the air up...
  20. Replies
    31
    Views
    14,793

    Congrats SgtToe! Very glad to see that you've...

    Congrats SgtToe! Very glad to see that you've ordered a kit!

    You set an ambitious but well thought our plan! I wish you the best in your build of both printer and enclosure, if there's anything I...
  21. Replies
    475
    Views
    226,855

    I agree with you usarmyaircav. I got similar...

    I agree with you usarmyaircav. I got similar cracks between layers when my fan accidentally turned on during an ABS print. I'm sure there are some circumstance where you would want the fan on for a...
  22. Cool thanks Roxy, I really appreciate the lead. I...

    Cool thanks Roxy, I really appreciate the lead. I am hoping to get ABL set up on my printer soon as this will help me get more familiar with the firmware!
  23. Sniffle, are you using this devel version of...

    Sniffle, are you using this devel version of octoprint? If you know where it is and it's not too much work, would you mind linking it here?
  24. Replies
    147
    Views
    79,385

    Ha! Yeah maybe 2 octopi setups! I'm going to...

    Ha! Yeah maybe 2 octopi setups!

    I'm going to be using 8mm thick glass I'm re-purposing from a broken digital bathroom scale as my "view port". I'm going to frame it with wood and use that as the...
  25. Replies
    16
    Views
    8,766

    Wow I've never seen anything like that before....

    Wow I've never seen anything like that before. It's pretty interesting to watch for sure.
Results 1 to 25 of 391
Page 1 of 16 1 2 3 4