Ok, so the instructable doesn't give any dimensions for the aluminum extrusion or the plexi...says look in Sketchup to figure out how much. I'm not familiar with Sketchup so I don't have a clue how...
Type: Posts; User: csader
Ok, so the instructable doesn't give any dimensions for the aluminum extrusion or the plexi...says look in Sketchup to figure out how much. I'm not familiar with Sketchup so I don't have a clue how...
Not sure why I'd need to...this one is working fine, and I'm sure I can adjust the settings so it doesn't raise quite so much after the G28...
Something I'm missing?
yep. Setting it to 18 kept it from lowering too far. Now after G28 (before sending a G29), it raises the nozzle a bunch, which is time consuming, but it's working and printing now, so I'm happy for...
You might just be a genius. Not near my printer at the moment to try, but this sounds like a winner. I'll report back for posterity.
Edit: Looking at the firmware right now, Z_RAISE_BEFORE_PROBING...
Yes, yes, and yes.
Yes, seems reasonable.
I went back into my firmware and re-ran the instructions from Zennmaster, followed by an M502 M500 pair, just in case. No luck.
I went back into...
I do have EEPROM enabled. I'm using Clough's firmware from his website, which had it enabled by default.
By resetting it, do you mean running an M502? When I do that, and try running G28 and G29...
Hey folks
Been sitting out for a while with a non-working printer. Had a meltdown and needed to replace some parts.
Getting around to replacing parts now and I'm trying to get ABL setup, but...
Anyone have one that works with S3D's new Dual Extruder Wizard? I'm using the original IBDE designs, not the Flex.
I have mine doing a G28, which triggers the X and Y endstops when it homes. Then it does ABL (G29) and doesn't hit the X or Y endstops at all.
I wonder if it has anything to do with Safe Homing?...
Hmmm...doesn't make sense to me why there would be any X offset if I'm printing with the right (facing the printer) nozzle...that sits pretty close to 0,0 when I home it.
Using Clough's firmware, adjusted for my 10" bed, calibrated nicely. However, my prints aren't printing in the center of the bed...they seem to be off by about 20mm on the Y axis, and 30mm on the X...
Jeez, I feel like I've got nothing but issues...
1. Here's a video of my extruders pushing out equal amounts of filament at the same speed and temp. Left extruder works fine. Right extruder seems...
Should I be able to see the e-steps for both extruders via the LCD? I only see one.
Using clough's configuration.h.
Probably not the place to post this, but since I'm using Cloughs configuration.h, I figure what the heck.
Having an issue where Z axis isn't homing on G28 or G29...I can move the z axis up and...
Sorry, I'm a little dull sometimes. Can you elaborate on what you mean by making sure there's no bind?
I'm assuming I should discconnect the threaded rod from the motors, then run the z-nuts up...
No matter what I do, I can't get the hotends level...my right side Z-nut spins itself out of the nut trap by the time the right side hotend touches the paper (see gap on right side in photo). I'm at...
That device you linked to is double the cost Colin's charging for a replacement board. Don't see the benefit.
Colin's assessment is a fried USB port. Ordered a replacement arduino.
Interesting idea...I'm not super familiar with the pinout on a Taurino 2560...which pins are TX/RX for serial? I think i have an extra USB to Serial cable lying around somewhere.
Yep, was working great for weeks. All of a sudden stopped working. Well aware of the one program at a time thing, so I don't think this is the issue.
This one's interesting. When I plug into...
Well, apparently this is a rare issue among the MakerFarm community, as I'm surprised not to have any responses with solutions or guidance.
While I wait for Colin to respond to my email, I found...
No other ideas? I tried contacting Colin, but he hasn't gotten back to me, which is abnormal for him...but he's human, so whatever.
I haven't changed it so I'm assuming Marlin is using 250000.
As for trying a different one, not sure how to do that some Arduino can no longer connect...
I tried it on my Mac and a Windows XP...
Strange issue today. I can't seem to connect to my printer via USB, either through Pronterface or the Arduino IDE...in pronterface I get the following
ERROR] Could not connect to...
Couldn't find the answer to this anywhere:
When wiring up the second extruder, I get that we use E1 for the motor and D9 for the heater. I'm assuming I use T2 for the thermistor? Is there anything...