Search:

Hey Oldtimer, Very good question, it shows you're thinking about this seriously before you jump in (but just jump in anyway... the water is great!)

The simple answer is yes the firmware controls...

I ran into a problem similar to this, where the print would start fine and then after 10 to 20 minutes it would be air printing. The filament was grooved by the hobbed bolt and would no longer feed....

I do the ABL every print Hankus. Yes it takes a few minutes, but in my estimation it is time well spent. One thing I do is move my start code for hotend heating to after the ABL completes so I don't...

Even 10fps should give smooth video over a LAN connection, at least it did with mine. I would guess it is wireless latency. With a 150mbs wireless dongle and 10fps mine was very smooth on the LAN,...

Teamviewer should provide the same results and give much better internet stream than the built-in Pi internet streaming TJC... great idea. And Teamviwer (also VNC) can be had for free. So even better.

DrBoost, Don't confuse the 12v 30amp DC output with the 110v AC input. The AC side is considerably lower amperage than the lower voltage DC output. The input specs on your power supply should list...

Your video should be pretty smooth if viewing from inside the LAN, but across the internet I have found it is very choppy and lags quite a bit behind the actual print. I haven't found a cure for the...

Check to make sure you don't have this line commented out in your configraton.h in the Bed Auto Leveling section.
#define PROBE_SERVO_DEACTIVATION_DELAY 300

This will cut power to the servo 300ms...

Yeah, I really would like a password for viewing. The main reason is that I don't want unfettered access to real-time build streaming of proprietary new designs I'm working on. But I still want to be...

Thanks again sniffle. I edited the haproxy.cfg and setup the port I wanted to use, setup the forwarding in my router and it's working exactly as intended.

It's hard to believe a $35 Raspberri Pi...

Thanks for the quick reply sniffle. This saves me a lot of searching. I'll set it up tomorrow as soon as my print job finishes.

Where is the config file for setting the forwarding port for camera viewing? I can set to a non-standard port and all features work except the camera viewing. I just haven't figured out how to set an...

Got my Pi 2 in yesterday and spent a little time setting up OctoPrint today. Went very smoothly and it was setup and running in about 30 minutes. I setup the recommended 300s for the communication...

Thanks for the reply. Since it's early days for the Pi2 I think I'll wait just a bit to see if there are any compiling issues before I jump. I'm sure it'll be worth the wait rather than getting the...

Has anyone tried a Rasberry Pi 2 yet with Octoprint? Gotta say I'm really interested in setting up a Pi with Octoprint and would prefer to get the 2 if it doesn't have issues other than no flash...

Great thread Zulfe, I've ben looking at this combo also. Not really because I'm experiencing any troubles with the stock setup, but well... it's shiny and machined. lol. I really like well machined,...

Glad to hear you got it figured out EMU! Now you need to implement a long term solution. A 9c differential in ambient temp must mean you are running on the ragged edge between a successful and...

All very good points Printbus. Keeping that in mind it might make sense to look at the part being printed and the orientation it is being printed in. If the part is much narrower in x than y, for the...

Here is the ID tag for the MakerFarm Nema17 motor I got with my kit that stays very cool.

http://3dprintboard.com/attachment.php?attachmentid=2537&d=1409686145&thumb=1

So if you want one from...

Why not just buy one of the new NEMA17's from MakerFarm and not worry about it. It's only 15.00 and that should solve any worry about heat. Get one for your extruder too. I bought my 10"kit at the...

The MakerFarm is a good choice. It is the most active printer group on the forum and that's worth the price alone. If you have a problem there is always well informed help, and there are lots of good...

At least with Slic3r (not sure about other slicing programs) the gcode will have M190 and M102 code to set bed temp and hotend temp. So if you have 60c for the bed in EEPROM and M190=100c, it will...

For my i3V 10 where I put the clip for my glass makes a major difference. When I moved my clips to the front and back of the printbed it took forever to reach 110c, and when I put them back on the...

Belts also stretch in the most used areas and little to none in the least used areas. So periodic belt replacement would be valuable after X hrs of use. What X represents I have no idea, but belt...

My LCD will go blank at random times, but always if the Z probe on the servo contacts the bed before retracting. The reason for me is the Arduino board doesn't have the voltage needed when the servo...