The filament pathway is sized for one or the other filament diameter depending on the extruder body .stl version you printed. so the extruder body can't do 2 different diameters as designed. it...
Type: Posts; User: TopJimmyCooks
The filament pathway is sized for one or the other filament diameter depending on the extruder body .stl version you printed. so the extruder body can't do 2 different diameters as designed. it...
to respond to the original post - My brother and I installed a BLtouch on his 10" I3v. we set it up like a servo and used the angles given by BL touch's directions. It worked fine. it is screwed...
If I ignore pronterface, which forces all alpha characters to UC, and use a gcode file with the LC n will it work? i'm on 1.1 rc 6 bugfix now. is the P implemented in rc 6 or yet to be changed?
...
Ok, I transferred all the information from configuration.h to the new one for RC6 bugfix and flashed it. I can't get it to home to the back right as my endstops are set up for (and as a lot of...
Ok, I did the change to #define AUTO_BED_LEVELING_GRID_POINTS 5
I went to pronterface, ran G28.
when I sent G29 n 2 i got this error message:
>>> g29 n 2SENDING:G29 N 2
Error:Line Number is...
Hi Roxy,
I am having a problem getting my G29 to probe four points only. This is the BeckDac fork from about 15 months ago. If it would help to update to newer marlin I could do so.
I have...
the filament check thing is easy. I had it figured out with a U shaped opto switch, left over from a pinball machine repair, that would trigger the z endstop. Laziness overcame me though.
My...
I ordered a meter of 3mm OD/2mm ID PTFE. I'm going to order a sampler pack of 1.75's to try, such as
http://www.amazon.com/Sunwin-1-75mm-Filament-Different-Printer/dp/B00N0A8YHI
Not planning...
Clough42 - I also have interest in 1.75 mainly for availability issues rather than function. However I have an inventory of 3mm and would like to cover both. Any chance of getting an STL of an...
What's the purpose of mounting a Bowden extruder on a moving carriage? Seems like you're getting the worst of both worlds there - the annoyances of Bowden without the accompanying light weight end...
BeerDart Engineering?
Do tell. Dglass?
Thanks for the detailed explanation.
what print area size, what Hotend, what power supply, where are you located? is it the makerfarm aluminum bed support plate, makerfarm aluminum heated bed plate? generic bed support plate? not...
Some have experienced problems with the wood bed frame warping with repeated heat cycles while printing ABS. Causes first layer variation within a single print and increases Z banding. If I was...
anybody got a makerfarm aluminum bed yet?
possibly the Geetech and RRD versions are different? I'm getting beyond my knowledge. might post on the wider reprap forums and see if someone is more up on it.
edit: looking at the pic- you...
If you go dissolvable, HIPS is more compatible with ABS and higher temp filaments. PVA is hard to print with and only PLA will begin to stick to it. You might have better luck with the flex...
command for the LED light pwm controls is:
M42 P5 S255 ; light on 100%- light is connected to RRD fan extender second plug. if you have a fan plugged in there should work the same.
M106 S255...
doubt pla will stick to ninjaflex but no experience. usually dissimilar filaments at dissimilar temps will not stick at all. the pla starting at the bed might give it a fighting chance.
your slicer is screwing up your support- it's offset and apparently not by the correct offset for your support nozzle. Slic3r does not offer a lot of control of infill density IIRC.
it's going...
the pin sockets are through hole mounted, so I just soldered 3 more pins worth of header to the butts on the other side facing out. Didn't explain very well but I just added pins onto what was there...
A greg's wade has enough ass to pull the filament in even if you use the makerfarm spool holder and it's a little sticky. Mine would only stop feeding when the filament was completely crossed up or...
self support with the ninjaflex. Or, change the file to be solid under the projection down to the bed and then cut away what you don't need after printing. (would have to go full infill at that...
In configuration.h designate control board or motherboard 34 instead of 33. should be it. near the beginning of the file. it's been a while so check back if that doesn't work.