Close



Dig deeper, search our News website




Search:

Type: Posts; User: Nihonddd

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    44,840

    Once the love affair with 3D scanners has...

    Once the love affair with 3D scanners has subsided I bet you end up just modelling it from scratch(like SF suggested).

    No, but seriously, you could model a propeller in maybe 1000 vertices.
  2. Have you tried applying a higher level of...

    Have you tried applying a higher level of subdivision to the object before exporting the model.
  3. Replies
    3
    Views
    3,280

    Your problem will probably disappear when you get...

    Your problem will probably disappear when you get that air funnel installed. If not reduce overall temps a little.
  4. Replies
    10
    Views
    5,136

    Yes, I can give you some advice....read all the...

    Yes, I can give you some advice....read all the other identical posts on this site, then, if you still have any questions, I am certain that you will receive more excellent advice.
  5. Replies
    10
    Views
    13,288

    B...l....e....n.....d.....e.....r!

    B...l....e....n.....d.....e.....r!
  6. Replies
    25
    Views
    59,269

    James-Its probably being caused by overheating...

    James-Its probably being caused by overheating the print. either lower the ambient room temp or reduce hotend/heatbed temp.
  7. Replies
    4
    Views
    3,569

    Allow me to add yet another possibility, that...

    Allow me to add yet another possibility, that your print is getting too hot?? You could try cooling down the ambient room temperature.
    Artifacts like these can show up on the overhangs and...
  8. Replies
    17
    Views
    10,903

    I'd say that if making 3D prints is important to...

    I'd say that if making 3D prints is important to you, that you should keep looking - there are lots of 3D modeling software alternatives out there these days.[/QUOTE]


    I recommend Blender. The...
  9. Replies
    8
    Views
    4,834

    If you want to keep cost down, avoid much of the...

    If you want to keep cost down, avoid much of the advice suggested on this thread your project is going to spiral in cost. Avoid investing large amounts of money. Invest your time instead.

    Don't...
  10. Replies
    8
    Views
    4,834

    Feasible yes, but not with out a pretty steep...

    Feasible yes, but not with out a pretty steep learning curve. I started out about 5 years ago with the same intentions to scan, edit and then 3d print.
    You are going to need a decent PC with a fair...
  11. Thread: Heads up!!

    by Nihonddd
    Replies
    0
    Views
    1,779

    Heads up!!

    One month on from my build, I have to say that I am getting very nice consistent results in PLA from my I3v printer. I am printing complex models but I turned the speed down and the details print...
  12. Replies
    5
    Views
    3,152

    "If you have a couple of extra plate nuts for the...

    "If you have a couple of extra plate nuts for the v-rails, the bow at the bottom could be removed by installing the plate nuts in the bottom of the y-bed v-rails so that the plate nuts push against...
  13. Replies
    5
    Views
    3,152

    Printbus. Thanks for your reply. I have...

    Printbus.

    Thanks for your reply.

    I have added the top piece and it has not remedied this. I will try out your T-slot suggestion.
    Actually my whole main frame piece is twisted by about 3mm when...
  14. Replies
    5
    Views
    3,152

    Makerfarm- Main Frame warp!

    I am just putting together my i3v 8".
    I am concerned that my frame might be a little warped, particularly the main section the piece the one with the Makerfarm laser tattoo. Has anyone else had a...
Results 1 to 14 of 17